Announcement

Collapse
No announcement yet.

1984 Katana 7/11

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Now comes the challenge of color-matching the silver of that beautiful gas tank for the rest of the parts..silver is tough. Not only the shade, but the metallic coarseness. Might be easier to re-paint it along with all the other parts. What the heck, it's only time and money, right..? Or am I assuming incorrectly that you're even painting the bodywork silver..?
    Last edited by nvr2old; 01-18-2018, 01:44 PM.
    1979 GS1000S,

    1982 Honda CX500 Turbo, 1982 Honda MB5 w/CR80 motor, 1977 Honda "nekid" Goldwing, 1976 Honda CB550F cafe', 1972 Honda XL250 cafe'

    Comment


      It sure is Charlie!!! Love getting those red and white labelled packets... and that tank... mmmm tasty!

      All good Larry, as nice as the tank looks it's going to get painted, going to have some trouble bringing myself to touch that paint but it's gotta be done. I'm undecided if I should strip it or just rub it back though. Best strip it I think.

      While the paint on that tank is very nicely done, it's not the correct 13L Suzuki Kat paint which saved me significantly on the tank price as I had to buy the paint anyway for the other bits.

      The plan is the 13L on the cowl, tank, front mudguard, and side covers. Then it'll be gloss black on the top part of the cowl and tank and rear part of the front mudguard as per the stock style Kat two tone paint jobs, and the tail piece will be gloss black.
      1982 GS450E - The Wee Beastie
      1984 GSX750S Katana 7/11 - Kit Kat - BOTM May 2020

      sigpic

      450 Refresh thread: https://www.thegsresources.com/_foru...-GS450-Refresh

      Katana 7/11 thread: http://www.thegsresources.com/_forum...84-Katana-7-11

      Comment


        You said it, Pete! That tank is tasty.

        I have seen a lot of pics of opening new parts boxes with a celebratory drink near by.
        Beverage of choice? haha.
        2@ \'78 GS1000

        Comment


          I wouldn't worry about stripping that tank, Pete. Just sand it with 600 wet and dry and you'll be good to go. It'll make the perfect base for you to do a re-spray over.
          1979 GS1000S,

          1982 Honda CX500 Turbo, 1982 Honda MB5 w/CR80 motor, 1977 Honda "nekid" Goldwing, 1976 Honda CB550F cafe', 1972 Honda XL250 cafe'

          Comment


            Haha yep Steve! Beverage of choice was a Burleigh Brewing Big Head (local brewing company, zero carb beer) which I very much enjoyed

            Cool Larry, that will cut down on the prep time a bit but also I'll be able to make sure I leave the tank sealed as is too, I was a bit worried about accidentally getting stripper on the seals over the petcock and filler openings so I can leave those intact now.

            Hopefully this weekend I can get a good move on finishing up the prep working and getting the shed sorted to get painting. I need to make up some frames for hanging bits and I need to improve the air flow in the filter box before I spray with 2K as well.
            1982 GS450E - The Wee Beastie
            1984 GSX750S Katana 7/11 - Kit Kat - BOTM May 2020

            sigpic

            450 Refresh thread: https://www.thegsresources.com/_foru...-GS450-Refresh

            Katana 7/11 thread: http://www.thegsresources.com/_forum...84-Katana-7-11

            Comment


              Not much to report from the weekend, although I did improve the air flow in the filter box. The fan's a bit close to the rear wall, so it felt like air was hitting the wall and blowing straight back instead of going around the corner.

              I added some angled material and it seems to flow better now. It was ok with the aersols but I really needed to address it before doing any 2K painting.

              Untitled by starpoint73, on Flickr

              Untitled by starpoint73, on Flickr

              I've been having trouble finding red pinstriping tape for the pinstripe that will run at the top of the silver under the black on the cowl and tank, but I lucked out at Autobarn of all places and the colour looks like it will work quite well.

              Untitled by starpoint73, on Flickr

              And out of curiousity I compared the tank with the 13L on the front side covers... no it's not 13L but it's close!

              Untitled by starpoint73, on Flickr

              Unfortunately I did discover that the gaskets I made for the anti dive block off plates are not working and fork oil is leaking from both. I guess I'm going to have to use some sort of sealant after all.
              1982 GS450E - The Wee Beastie
              1984 GSX750S Katana 7/11 - Kit Kat - BOTM May 2020

              sigpic

              450 Refresh thread: https://www.thegsresources.com/_foru...-GS450-Refresh

              Katana 7/11 thread: http://www.thegsresources.com/_forum...84-Katana-7-11

              Comment


                That material should definitely help airflow. In ductwork they put turning vanes on supply side 90 degree elbows to guide the air around the corner and reduce turbulence.
                sigpic
                When consulting the magic 8 ball for advice, one must first ask it "will your answers be accurate?"

                Glen
                -85 1150 es - Plus size supermodel.
                -Rusty old scooter.
                Other things I like to photograph.....instagram.com/gs_junkie
                https://www.instagram.com/glen_brenner/
                https://www.flickr.com/photos/152267...7713345317771/

                Comment


                  Ah ok, having never done anything like that before I didn't give it the slightest thought... until last time I was spraying in there I noticed the inlet filter material moving a bit and felt some air coming back *out* at me...
                  1982 GS450E - The Wee Beastie
                  1984 GSX750S Katana 7/11 - Kit Kat - BOTM May 2020

                  sigpic

                  450 Refresh thread: https://www.thegsresources.com/_foru...-GS450-Refresh

                  Katana 7/11 thread: http://www.thegsresources.com/_forum...84-Katana-7-11

                  Comment


                    I finally got some time back on the Kat yesterday.

                    The front mudguard is now ready for high build primer and I got a good start on preparing the tail piece as well.

                    Untitled by starpoint73, on Flickr

                    I'm going to need a bit more than just the high build primer on the tail piece, it's got a few reasonably deep war wounds.

                    I also have another plastic repair to do after hearing a crack while sanding it. On the inside was a piece of stiff rubbery material glued on and that and the paint were masking a nice big crack on the right side.

                    Untitled by starpoint73, on Flickr
                    1982 GS450E - The Wee Beastie
                    1984 GSX750S Katana 7/11 - Kit Kat - BOTM May 2020

                    sigpic

                    450 Refresh thread: https://www.thegsresources.com/_foru...-GS450-Refresh

                    Katana 7/11 thread: http://www.thegsresources.com/_forum...84-Katana-7-11

                    Comment


                      I broke out the acetone, ABS offcuts, and soldering iron last night and got stuck into the plastic repairs.

                      I started on the choke lever which had one of the clips broken off.

                      Untitled by starpoint73, on Flickr

                      Not sure how well that will work as there's not a lot of material there to get to bond. I need to clean the repaired area up so it will go back together properly then I'll know if it's a good repair or not.

                      Untitled by starpoint73, on Flickr

                      Then onto the tail piece.

                      I was hoping to only repair from the inside, but that wasn't strong enough alone so I had to go from the outside also.

                      A bit of ABS slurry pushed into the crack and then the soldering iron across it on both sides and it's nice and strong.

                      Untitled by starpoint73, on Flickr

                      Untitled by starpoint73, on Flickr

                      I then added a bit more slurry on the outside as a bit of a filler so I don't end up with more low spots.

                      Untitled by starpoint73, on Flickr

                      And finally there were some divets and small chunks taken out on the bottom edge towards the front that I used more slurry as a bit of a filler for.

                      Untitled by starpoint73, on Flickr

                      Untitled by starpoint73, on Flickr

                      That all just needs a sand back and tidy up now and it should be good to finish the paint prep.
                      1982 GS450E - The Wee Beastie
                      1984 GSX750S Katana 7/11 - Kit Kat - BOTM May 2020

                      sigpic

                      450 Refresh thread: https://www.thegsresources.com/_foru...-GS450-Refresh

                      Katana 7/11 thread: http://www.thegsresources.com/_forum...84-Katana-7-11

                      Comment


                        How did I miss this update till now..? Nice progress on your plastic parts, Pete. Looks like you have the cracks and low spots under control with your slurry. I'm as anxious as you, I'm sure, to see everything in primer. That is such a good feeling of accomplishment when you get to that stage.
                        1979 GS1000S,

                        1982 Honda CX500 Turbo, 1982 Honda MB5 w/CR80 motor, 1977 Honda "nekid" Goldwing, 1976 Honda CB550F cafe', 1972 Honda XL250 cafe'

                        Comment


                          Cheers Larry! I did have to go back over it again after initial sanding, found a few other spots that needed filling.

                          Unfortunately I've become very time poor over the last 3 to 4 weeks, so I've not had any time to really finish up the prep which is very frustrating given how close I am to putting high build primer on them.

                          Hopefully I can get stuck back in soon because I'm really keen to get the primer done.
                          1982 GS450E - The Wee Beastie
                          1984 GSX750S Katana 7/11 - Kit Kat - BOTM May 2020

                          sigpic

                          450 Refresh thread: https://www.thegsresources.com/_foru...-GS450-Refresh

                          Katana 7/11 thread: http://www.thegsresources.com/_forum...84-Katana-7-11

                          Comment


                            Finally back to it yesterday. Didn't get a huge amount of time but at least the tail piece is now ready for high build primer.


                            Untitled by starpoint73, on Flickr


                            I also got a quick start on the side covers but these won't need high build primer, they're all pretty smooth. I just need to get them keyed enough to take primer and paint.


                            Untitled by starpoint73, on Flickr


                            I've booked in leave from work the last week in March and first two of April, so I'm aiming to get the high build primer done before then, which should mean I can at least get the painting done.


                            Ideally I'd like to get the crankcase paint done as well and hopefully during that time off I can find someone to weld second gear on also... which reminds me a I need to chamfer the gear ready for it to be pressed on and welded too.
                            1982 GS450E - The Wee Beastie
                            1984 GSX750S Katana 7/11 - Kit Kat - BOTM May 2020

                            sigpic

                            450 Refresh thread: https://www.thegsresources.com/_foru...-GS450-Refresh

                            Katana 7/11 thread: http://www.thegsresources.com/_forum...84-Katana-7-11

                            Comment


                              Been a while Pete, whats up??
                              I build Pipers

                              Comment


                                It has indeed been a while! You have good timing though...

                                For the first time in what feels like months (only been a few weeks) I actually got to make some progress today.

                                My evenings have been learning new stuff for work, and the weekends have been humid and wet and no good for painting. The humidity was still a little high today but I said to hell with it and got stuck in.

                                All set up and plastic primer/adhesion promoter on the tail piece and front guard:

                                Untitled by starpoint73, on Flickr

                                Got the high build primer done. If you look close you'll see lots of runs and lumps and bumps, and that's due to brushing on the first coat as suggested by the mob I bought the paint from. Seems like it was a good suggestion as it definitely seemed to fill in the little pock marks and so forth in the bare fibreglass on the front cowl.

                                Untitled by starpoint73, on Flickr

                                And I got my interpretation of a guide coat on as well, some areas are probably a bit too heavy but it should still do the job.

                                Untitled by starpoint73, on Flickr

                                I have three weeks leave from work after this week, so I'm hopeful I'll get sufficient time to get all the bodywork painted as well as the crankcases. I'm expecting the first week will be wet, so that'll be lost for painting but at least I'll get the guide coat sanded.

                                As a side note, I'm really stoked how well my shed is working. I was a bit concerned the 2K paint would be an issue compared with the aerosols, but not at all. The improvements in airflow in the filter box are probably helping, but between coats there was pretty much no smell outside the shed aside from a hint of thinners.
                                1982 GS450E - The Wee Beastie
                                1984 GSX750S Katana 7/11 - Kit Kat - BOTM May 2020

                                sigpic

                                450 Refresh thread: https://www.thegsresources.com/_foru...-GS450-Refresh

                                Katana 7/11 thread: http://www.thegsresources.com/_forum...84-Katana-7-11

                                Comment

                                Working...
                                X