Announcement

Collapse
No announcement yet.

Springs specs

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Springs specs

    Do old springs get longer or shorter? The specs for my front fork springs are 20.3". The old ones measure 21.25" so they seem to have stretched. My new progressive springs came in measuring only 18" which surprised me. In BassCliff's write up, the pics showed his progressive springs to be longer than his stockers and that is what I was expecting. I guess I will be using a long spacer according to the Progressive instructions. Since my springs will be about 2" shorter than the original ones, I think my spacers will need to be longer than the stock ones which are 3 1/8". The PVC spacer material included with the Progressives is 10" so if I cut it in half, I will have to 5" pieces. Does that seem awful long.
    1983 GS 1100 Guided Laser
    1983 GS 1100 G
    2000 Suzuki Intruder 1500, "Piggy Sue"
    2000 GSF 1200 Bandit (totaled in deer strike)
    1986 Suzuki Cavalcade GV 1400 LX (SOLD)

    I find working on my motorcycle mildly therapeutic when I'm not cursing.

    #2
    Well I found some data for a 1000L (Maybe close enough) that says the springs should start out at 21.3 with a service limit of 20.3 so I guess they shorten and my original springs are almost at the starting spec (Maybe the 6000 miles on my bike when I bought were actually accurate.)
    Anyway, does anyone have an opinion on the 18" springs that Progressive sent me? Does 18 inches raise any red flags?
    1983 GS 1100 Guided Laser
    1983 GS 1100 G
    2000 Suzuki Intruder 1500, "Piggy Sue"
    2000 GSF 1200 Bandit (totaled in deer strike)
    1986 Suzuki Cavalcade GV 1400 LX (SOLD)

    I find working on my motorcycle mildly therapeutic when I'm not cursing.

    Comment


      #3
      Which ones did you get? 11-1107 is the replacement. I think I ended up using approx 2" of the PVC spacers each side in addition to the spacers in the fork.

      82 GS850L - The Original http://s224.photobucket.com/albums/d...ePics067-1.jpg
      81 GS1000L - Brown County Hooligan http://s224.photobucket.com/albums/d...ivePics071.jpg
      83 GS1100L - Super Slab Machine http://s224.photobucket.com/albums/d...t=DCP_1887.jpg
      06 KLR650 - "The Clown Bike" http://s224.photobucket.com/albums/d...nt=SERally.jpg
      AKA "Mr Awesome"

      Comment


        #4
        Thanks TWR. Yes, I got the 11-1107. Was that on your 1100GL or your 1000L? Since the new springs are 3 inches shorter than what came out, I'm thinking using 3" PVC plus the original spacer should bring me to about the top of the fork. I'm not sure of how the new springs affect preload requirements. Should I end up with my spacer a little higher out of the fork with the new springs or maybe lower?I sent u a PM after reading one of your old posts about this. While I'm on this subject, I keep reading about folks changing their spacers. Is it possible to do this without taking the forks off the bike? Jim M
        1983 GS 1100 Guided Laser
        1983 GS 1100 G
        2000 Suzuki Intruder 1500, "Piggy Sue"
        2000 GSF 1200 Bandit (totaled in deer strike)
        1986 Suzuki Cavalcade GV 1400 LX (SOLD)

        I find working on my motorcycle mildly therapeutic when I'm not cursing.

        Comment


          #5
          Jim, you can change the spacer without taking the forks off the bike to adjust your final preload if needed. I would recommend taking the forks off the bike and taking them completely apart when you do the initial install so you can fully inspect the sliders, teflon bushing, and flush out the tubes. Check Basscliffs site for the instructions on how to do it and you will need the "special tool" to get the damper rod out. The parts fiche makes it look like a tough job with all the pieces but in reality it is not that hard to do.

          Use some blue loctite on the allen bolt to re-assemble and you should be good to go. I am using the Pro Moly seals and dust boots. If you use them do not hammer them in, they will leak. Just push them lightly so you can get the washer and circlip over them and that is it.
          82 GS850L - The Original http://s224.photobucket.com/albums/d...ePics067-1.jpg
          81 GS1000L - Brown County Hooligan http://s224.photobucket.com/albums/d...ivePics071.jpg
          83 GS1100L - Super Slab Machine http://s224.photobucket.com/albums/d...t=DCP_1887.jpg
          06 KLR650 - "The Clown Bike" http://s224.photobucket.com/albums/d...nt=SERally.jpg
          AKA "Mr Awesome"

          Comment


            #6
            Thanks again and yes, I have everything apart and cleaned up well. Was just wondering if I could shorten a spacer after I have everything reassembled without total reassembly. Your help is greatly appreciated. Jim M
            1983 GS 1100 Guided Laser
            1983 GS 1100 G
            2000 Suzuki Intruder 1500, "Piggy Sue"
            2000 GSF 1200 Bandit (totaled in deer strike)
            1986 Suzuki Cavalcade GV 1400 LX (SOLD)

            I find working on my motorcycle mildly therapeutic when I'm not cursing.

            Comment

            Working...
            X