Announcement

Collapse
No announcement yet.

Adjusted the clutch...now can't ride. What?!

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Adjusted the clutch...now can't ride. What?!

    Noticed the clutch was slipping in 4th and 5th this morning.

    So, I adjusted the clutch according to Clymer's and it slipped in every gear.

    Tried again and the bike wouldn't move.

    Tried again and the clutch wouldn't disengage so it was pulling all the time.

    Any suggestions?

    #2
    I adjust mine when it is hard to get into neutral. I suppose that's caused by cable stretch. The adjustments can move the engagement closer to, or farther from the grip, but there is always a very narrow space between engaged and disengaged. Personally I like mine close to the grip. From your description it sounds like it might be time for a clutch replacement.
    '78 GS1000E, Dyna-S ignition, Dyna Green Coils, K&N pods, Delkevic SS 4-1 exhaust, Dynojet Stage 3 jet kit, Russell SS Brake Lines, Progressive suspension, Compu-Fire series Regulator 55402 and Advmonster cree LED headlight conversion.

    Comment


      #3
      Might want to check your clutch springs and see what their measurements are. If they are past the service limit - replace them.
      sigpic
      Cowboy Up or Quit. - Run Free Lou and Rest in Peace

      1981 GS550T - My First
      1981 GS550L - My Eldest Daughter's
      2007 GSF1250SA Bandit - My touring bike

      Sit tall in the saddle Hold your head up high
      Keep your eyes fixed where the trail meets the sky and live like you ain't afraid to die
      and don't be scared, just enjoy your ride - Chris Ledoux, "The Ride"

      Comment


        #4
        Also what's your cable like? Old or new? If it's old it could be stretched beyond usefullness meaning no amount of adjustment will make it work right, same deal if it's frayed somewhere along it's length, that will cause it to stretch as you work the clutch...
        1982 GS450E - The Wee Beastie
        1984 GSX750S Katana 7/11 - Kit Kat - BOTM May 2020

        sigpic

        450 Refresh thread: https://www.thegsresources.com/_foru...-GS450-Refresh

        Katana 7/11 thread: http://www.thegsresources.com/_forum...84-Katana-7-11

        Comment


          #5
          All of that could be the issue and I'll check, but it was running pretty well until I "helped" it.

          Cable could be original.

          Comment


            #6
            Originally posted by oldrookie View Post
            Noticed the clutch was slipping in 4th and 5th this morning.

            So, I adjusted the clutch according to Clymer's and it slipped in every gear.

            Tried again and the bike wouldn't move.

            Tried again and the clutch wouldn't disengage so it was pulling all the time.

            Any suggestions?
            You adjusted it wrong.

            You need a little freeplay at the lever, but not too much.

            Regardless of adjustment, the clutch will slip if the springs and/or the plates are worn.
            Last edited by Nessism; 08-18-2011, 02:20 PM.
            Ed

            To measure is to know.

            Mikuni O-ring Kits For Sale...https://www.thegsresources.com/_foru...ts#post1703182

            Top Newbie Mistakes thread...http://www.thegsresources.com/_forum...d.php?t=171846

            Carb rebuild tutorial...https://gsarchive.bwringer.com/mtsac...d_Tutorial.pdf

            KZ750E Rebuild Thread...http://www.thegsresources.com/_forum...0-Resurrection

            Comment


              #7
              Yea, pretty sure you are correct, Nessim.

              Been fighting with it. I adjusted the helix screw as instructed by the manual. Set the play in the cable. No tire rotation.

              Move the helix screw out half a turn, tire starts rotating without regard to where the clutch is. Put the screw back to where it was...tire still rotates. Lather, rinse, repeat half a dozen times.

              Like trying to pin jello to the wall. Can't get a bead on where the helix screw is supposed to be since the reaction to any change to it defies logic.

              Comment


                #8
                You should not be pushing in the clutch rod at all with the adjustment at the sprocket. Make it so it is loose and make the final adjustment at the hand lever.
                1983 GS 1100E w/ 1230 kit, .340 lift Web Cams, Ape heavy duty valve springs, 83 1100 head with 1.5mm oversized SS intake valves, 1150 crank, Vance and Hines 1150 SuperHub, Star Racing high volume oil pump gears, 36mm carebs Dynojet stage 3 jet kit, Posplayr's SSPB, Progressive rear shocks and fork springs, Dyna 2000, Dynatek green coils and Vance & Hines 4-1 exhaust.
                1985 GS1150ES stock with 85 Red E bodywork.

                Comment


                  #9
                  Originally posted by chef1366 View Post
                  You should not be pushing in the clutch rod at all with the adjustment at the sprocket. Make it so it is loose and make the final adjustment at the hand lever.
                  Listen to chef here.

                  The adjustment screw at the helix should be tightened until it just contacts the push rod, then you back it off 1/8 - 1/4 turn and set the lock nut. After that, tighten the cable adjusters to get the free play at the lever as needed.
                  Ed

                  To measure is to know.

                  Mikuni O-ring Kits For Sale...https://www.thegsresources.com/_foru...ts#post1703182

                  Top Newbie Mistakes thread...http://www.thegsresources.com/_forum...d.php?t=171846

                  Carb rebuild tutorial...https://gsarchive.bwringer.com/mtsac...d_Tutorial.pdf

                  KZ750E Rebuild Thread...http://www.thegsresources.com/_forum...0-Resurrection

                  Comment


                    #10
                    Okay. I'll take another shot at it.

                    Comment


                      #11
                      Trying to do as you tell me. Not sure of what the symptoms tell me.

                      I've got it moving under its own power, but the clutch slips. It'll move as long as I don't hit the gas too hard and rev it up.

                      I loosened the lock nut, backed the helix screw out two turns and then tightened it down until the resistance was significant, backed it off 1/2 turn and locked the nut down. Then began to adjust the cable with the adjuster in the case. Used the one at the handlebar at the last resort.

                      I can't get the bike to move unless the clutch cable is tighter than it should be.

                      Clutch? Cable? Nut trying to adjust them?

                      Comment


                        #12
                        Step 1) Turn in the cable adjusters at both the handle bar lever and where the cable goes into the case. You want maximum cable free play at the lever.

                        Step 2) Loosen the lock nut on the adjuster.

                        Step 3) Turn in adjuster until you JUST START TO FEEL resistance then back the adjuster off 1/4 turn and tighten locknut.

                        Step 4) Check feel at the lever. There should be some free play at the lever, but not a whole lot. If you don't know what free play is please ask.

                        Step 5) If necessary, tighten the cable further until you have a small amount of cable free play with the lever released, but not much. You must have lever free play or the clutch will slip.

                        Please follow these steps and report back.
                        Ed

                        To measure is to know.

                        Mikuni O-ring Kits For Sale...https://www.thegsresources.com/_foru...ts#post1703182

                        Top Newbie Mistakes thread...http://www.thegsresources.com/_forum...d.php?t=171846

                        Carb rebuild tutorial...https://gsarchive.bwringer.com/mtsac...d_Tutorial.pdf

                        KZ750E Rebuild Thread...http://www.thegsresources.com/_forum...0-Resurrection

                        Comment


                          #13
                          Will do. That's a bit different than the Clymer manual, but I don't trust it much. Prefer the voice of experience. Will give this a try tomorrow.

                          Can't believe I got through the valve adjustment process and can't get the crazy cable adjusted correctly.

                          Thanks for the patience and the help.

                          Comment


                            #14
                            Oh, re: free play, the manual says 4mm. Assume that to be correct?

                            Comment


                              #15
                              Originally posted by oldrookie View Post
                              Oh, re: free play, the manual says 4mm. Assume that to be correct?
                              I don't know how they measure free play but regardless...

                              When you first pull the hand lever there should be a short amount of lever travel where slack in the cable is being taken up but there should be no real resistance felt. That is free play.
                              Ed

                              To measure is to know.

                              Mikuni O-ring Kits For Sale...https://www.thegsresources.com/_foru...ts#post1703182

                              Top Newbie Mistakes thread...http://www.thegsresources.com/_forum...d.php?t=171846

                              Carb rebuild tutorial...https://gsarchive.bwringer.com/mtsac...d_Tutorial.pdf

                              KZ750E Rebuild Thread...http://www.thegsresources.com/_forum...0-Resurrection

                              Comment

                              Working...
                              X