Announcement

Collapse
No announcement yet.

I wanna do the 2 step...

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    I wanna do the 2 step...

    Here we go... I need a little info.


    Is this a 2 step for launch mode?
    Curt
    Last edited by bellucci; 02-06-2012, 02:05 PM. Reason: photo upload
    sigpic'85 GS1150 1428 14-1 200+hp Hang On

    #2
    got a cleaner url?

    Comment


      #3
      Let me get that for you...

      EDIT: nevermind... you figured it out.
      Last edited by Guest; 02-06-2012, 05:51 PM.

      Comment


        #4
        Looks like one to me, a drl400.
        Dee Durant '83 750es (Overly molested...) '88 gl1500 (Yep, a wing...)

        Comment


          #5
          Marvelous... next one, maybe rev limiter?

          Thanks in advance
          Curt
          sigpic'85 GS1150 1428 14-1 200+hp Hang On

          Comment


            #6
            Yes that is a module that plugs in to the MSD box. Instead of swapping out pills you can dial in your rev limiter by twisting the knob.

            That is the MSD part 8673 7.6k to 9.8k

            Comment


              #7
              O.K. thanks... The last pics are more complicated and I will have to read up on the all clutch system... But if you guys want to give the readers digest version,why not.
              Curt



              sigpic'85 GS1150 1428 14-1 200+hp Hang On

              Comment


                #8
                Air shifter... Typically all provisions are left in place for normal operation. Clutch, cable and foot shifter... The air shifter cylinder is connected to the shift linkage. when you want to use the air shifter you just push the button. The box will cut the engine for a split second, up shift then resume the engine. It happens extremely quick so it just sounds like a seamless change.

                Not sure all what you wanted to know about it.




                Oh you will still have to use the clutch to launch.

                Comment


                  #9
                  I thought that there was a type of clutch release using air pressure... I could be wrong... Lets see if anyone else is bored and watching this thread. Thanks for the info...
                  sigpic'85 GS1150 1428 14-1 200+hp Hang On

                  Comment


                    #10
                    Aint not thang


                    Dance by me close - tell 'em all to go
                    One's for the money - but I'm through with the show
                    Move with me gently, oh so slow
                    Hold me and maybe we'll never let go, never let go
                    I'm through with sneakin' - been cutting it close
                    Through with the two-step, where the rhythm is law
                    Through with the two-step, where the rhythm is law
                    Oh, yes, it's love in any key
                    You opened up the door - now I know it's got to be

                    Now my cards on the table - hands on the deck
                    Now A is for able - no words - pause for breath
                    My willing baby, now can't you see
                    Little girl, it's not for me
                    So you waltzed into my life - one two three
                    Warmed up your smile - oh let it please be me, please let it be me
                    You swish and swirl - oh, swing and sway
                    Stay till the sun comes, and don't go away --

                    Comment


                      #11
                      I see only 1 button in your pictures

                      The DYNA DRL 400 is a very important addition to a "S" ignition for over rev protection- even if you do not use the 2 step feature.

                      lo limit setting is the 2step rpm cutout speed -it takes over when the purple and red wires are connected. the upper and lower setting are marked on the left dial scale - pic shows it is set at 9500

                      hi setting is the overrevving hi side rpm cutout --it is always working when the unit is on -- set the hi linit side no higher than 10,000 (shift at 9000)or 10,500 (shifting at 10K)-- it will start to kill the ignition and save the engine-if you miss a shift or while in the water box doing the burn out. A "dyna S" ignition alone will rev to the moon uncontrollably

                      I am guessing the MSD dial controls your shift light / shifting event-- hooked directly to the coils for a signal I presume -- should also be to a shift light or a air solenoid thru a on/off switch (automatic).. I like manual button shifting because spinning the rear tire and hitting the shift RPM will have it shifting when it shouldn't. I do not see a second button for shifting -- is it there? or is the MSD hooked to a air solenoid?


                      You have a standard relay and a electric air valve solenoid connected to the 2 step launch button circuit to control the clutch lever release.

                      Pull in the clutch lever- push the button -let go of the clutch lever while holding the button AND throttle wide open.

                      the clutch lever will release when you release the 2 step / launch button.

                      however I do not see the shifter button -- it may be set up for AUTO shifting directly off of the MSD unit. Just remember to turn the shifter on after doing the burn out AND the control unit has to be set lower than the launch RPM. -in the pictures it is set to shift gears while you are on the 2step.. (9500 launch and 9000 shift)

                      no worries belucci I'll get you acquainted with the operation - or change it to your fit your style. your calls/visits are always welcome
                      Last edited by trippivot; 02-07-2012, 12:55 PM.
                      SUZUKI , There is no substitute

                      Comment


                        #12
                        I knew I could count on you... now,I have to get the negotiating on schedule...

                        I got to see my motor in pieces today... The pistons have come back from MTC for the ring groove being recut for the new style rings. We also have wilder cams and new springs along with a new cam chain and guides. I was in bike porn heaven. It should be together in a couple of weeks...Everything else was fine. The cams will be retimed for track only if I get the other frame... Can you tell I am getting excited...
                        Curt
                        sigpic'85 GS1150 1428 14-1 200+hp Hang On

                        Comment


                          #13
                          That is an air clutch setup. It is so you can use a delay box & use a button to let the clutch go. It has nothing to do with the air shifter.

                          Comment


                            #14
                            this MSD unit does what for a clutch release?

                            I believe it is for a shift light ..




                            Originally posted by bellucci View Post
                            Marvelous... next one, maybe rev limiter?

                            Thanks in advance
                            Curt
                            SUZUKI , There is no substitute

                            Comment


                              #15
                              Well guys, so much for that bike. Someone else beat me to it... so we start over...
                              Curt
                              sigpic'85 GS1150 1428 14-1 200+hp Hang On

                              Comment

                              Working...
                              X