Announcement

Collapse
No announcement yet.

Shindengen SH775 plugs

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Gregory
    replied
    Originally posted by mvalenti View Post
    rule of thumb I use is if it smells like vinegar, keep it away from metals.
    I recently used some of this http://www.homedepot.com/p/Seal-All-...0113/100372161 as an over coat/sealer to electrical tape when I ran out of shrink tube.

    This is what I used. I smelled it and it doesn't smell like vinegar to me, cannot find the word acetic on the tube though - 100% silicone: http://www.homedepot.com/p/GE-II-Win...-24C/100026175

    Leave a comment:


  • mvalenti
    replied
    rule of thumb I use is if it smells like vinegar, keep it away from metals.
    I recently used some of this http://www.homedepot.com/p/Seal-All-...0113/100372161 as an over coat/sealer to electrical tape when I ran out of shrink tube.

    Leave a comment:


  • Gregory
    replied
    Originally posted by Grimly View Post
    Depends. The pure-cure silicone is acetic-free and won't harm anything, but the vast majority of available domestic silicone is the acetic acid cure stuff and I don't let that on wiring components. Easiest source for pure-cure acetic-free silicone is the stuff that's used for building aquaria.
    ok thanks, I will check the tube

    Leave a comment:


  • Grimly
    replied
    Originally posted by Gregory View Post
    2. I had some 100% silicone laying around and used that instead of RTV sealant...is there any downside to that?
    Depends. The pure-cure silicone is acetic-free and won't harm anything, but the vast majority of available domestic silicone is the acetic acid cure stuff and I don't let that on wiring components. Easiest source for pure-cure acetic-free silicone is the stuff that's used for building aquaria.

    Leave a comment:


  • Gregory
    replied
    Originally posted by 1980GS1000E View Post
    I installed the 775 where the ignitor box was and relocated the ignitor to where the old r/r was. I just used spade terminals filled with rtv. I also sealed up the ignitor box as this was a concern.
    Thanks for that tip, that is what I ended up doing also. I moved the igniter box from the battery box location to where the old RR was (one bolt fit and it hangs diagonally), And by elongating one of the holes on the sh775 was able to bolt right up to the old igniter location with some rubber washers between the bracket and Regulator for more air flow.. I do have 2 questions though................

    1. Does there need to be a fuse or circuit breaker between the sh775 and the battery? I thought I may have read that but cannot find that info now.

    2. I had some 100% silicone laying around and used that instead of RTV sealant...is there any downside to that?

    Leave a comment:


  • jbthomp
    Guest replied
    I have the triumph harness for the sh775 if you want it. I didn't use it on my 550 because the connectors were too big to clear the rear fender. It's yours if you want it just pay postage!

    Leave a comment:


  • MAC10
    Guest replied
    Yes it is posrplayer! I meant to say wired directly to the rr.

    Leave a comment:


  • posplayr
    replied
    Originally posted by MAC10 View Post
    Thanks Steve, and Nessism. I will check connections and run the tests again. This is a brand new Rick's stator, and should not be faulty.Stator wired straight into the battery as recommended here, and diligently followed.

    Hope that is a mistype............................

    Leave a comment:


  • rwnielsen
    Guest replied


    Poke around here. He has a set of plugs that you can assemble yourself all the way through complete harnesses. He ships immediately and answers emails. First class operation

    Leave a comment:


  • MAC10
    Guest replied
    SH 775 installation in a GS1000C tips

    I used a couple of pieces of one eighth inch aluminum plate to build a better mounting, which pieces are flat against the back of the rr which is itself aluminum as a heat sink. The whole thing bolts to the original electical mounting plate on the bike. I had to drill one extra hole to get the bigger SH 775 a place to bolt. A tight fit, but doable. The original Suzuki ignition solenoid is smaller, and will work better than my bigger aftermarket version.


    Due to the tight fit , I used spade terminals. At first try it would only charge at 13 to 13.3 volts.So...

    This season I re- did the connections from the SH 775 to the three stator wires. I scrubbed the three spade terminals on both ends before assembly, and crimped them tight with needle nose pliers, which is what I have. I cut down the plastic skirt on the rr to improve access to the connections.The way it came from the factory was too deep for my application. It is now about half the height, which lets it fit better in the crowded space, and be easier to work on. Filed smooth it looks original. After I verified it was producing a good charge, I filled it with rtv as recommended. I will add a little support to the wires with a zip tie to prevent stress on the now hanging wires.

    The centre of the three wires from the stator was a bit loose, which was the cause of the charging problem.

    The bike now sits at a solid 14.3 volts at anywhere over 2000 rpm. At idle it drops to 12.9.

    Next step is to test my electric vest to see how the new charging system copes with it.
    Last edited by Guest; 07-28-2014, 09:35 PM.

    Leave a comment:


  • tom203
    replied
    Originally posted by silverbullet132 View Post
    I was going to put a FH020AA on my GS as I have used one on my VFR, bad idea?
    Honestly, I think the series SH775 is superior and well worth $70 - it limits stator current output to what your bike needs at any moment rather than running at full tilt all the time.

    Leave a comment:


  • silverbullet132
    Guest replied
    I was going to put a FH020AA on my GS as I have used one on my VFR, bad idea?

    Leave a comment:


  • 1980GS1000E
    replied
    I installed the 775 where the ignitor box was and relocated the ignitor to where the old r/r was. I just used spade terminals filled with rtv. I also sealed up the ignitor box as this was a concern.

    Leave a comment:


  • Nessism
    replied
    So the stator wires are feeding directly to the R/R right? If so, that much is good.

    Voltage loss from R/R power output on the way to the battery is common. There are a couple of terminal connections in the circuit. You may need to remove the brass terminals from the plastic plug connectors and dip them in HCl acid or maybe vinegar to clean. Also scrub down the terminals with a stainless steel brush and pinch closed the prongs on the terminal. It idea is to make sure you don't have any extra resistance in the circuit.

    Leave a comment:


  • GSJim
    replied
    Originally posted by robertbarr View Post
    Someone should mention that the terminals that come with the kits are 'open barrel', and require a crimping tool specifically for that purpose. Anything else is just troglodyte.

    Personally, I love open barrel, but it takes a good tool and a little practice. Nothing wrong with letting someone else handle it -- which is slowly becoming my standard motto anymore.
    I used the ratcheting tool from Vinatge Connections ($35) for my open barrel terminals. After a few practice crimps I was able to get consistent crimps.

    Jim

    Leave a comment:

Working...
X