1977 GS750e project

[Sam 78 GS750]

Are you talking about # 27 in this diagram? --->https://www.partzilla.com/catalog/su...o-gs750e-19995

It's a bit hard to see in the fiche, but if you mean what I think you mean, you're right about where it goes. It's what keeps tension on the adjuster arm for synchronizing the carbs...

[Chuck78]

Inside the slide! The throttle return spring would do the job that placing it in the venturi would, no way the engineers would ever create turbulence in the venturi like that...

The slide is machined different and has a recessed well that the spring sits in on those models. I think that's the later version(?)

Is it inside the slide under the clip, or outside the slide in the venturi where the needle goes into the main jet?

[Chuck78]

Some VM carb slides are made for a spring under the needle, some are made for no spring.

So, finally got the rest of my parts to finish the project and my carbs back from cleaning, they didn't charge me anything!

Now after two months of have the carbs a part I've forgotten where the third spring goes. I think it's in the slide assembly inside the arm of the slide at the bottom with that little piece of metal on top and the adjuster on top of that. It would be really nice to see a schematic of the VM carbs.

What got got me worried was when I saw the picture on Bikecliff's for VM carbs, there's a picture of the slide and a spring under the needle, that can't be right? Right?

[Sam 78 GS750]

I went to the nearest Mom and Pop shop, there are no peps and auto z's here........So, I asked him how much it would be, he just smiled and said bring them by and will try it out together. Solid guy.

Pep Boys and Auto Zone are super convenient, and they have most of what you need... but things like that right there is why I'd rather have 1 good mom and pop shop over a million well stocked chain stores any day.

The chains pushed out damn near all of the mom and pop operations here in the states along time ago. The chains carried everything in the store. People went there because you could get things right now instead of the "I'll order it for you, it should be here in a couple of days..." answer from the mom and pop.

Funny thing is that the chains are becoming less and less convenient. Their in store inventory is down to what the mom and pop stores used to carry, because everything else has been moved to their website. So now the answer from the chain is "We don't have it in stock. I can order it for you, should be here in a couple of days...or you can just go to our website."

We're back to waiting days for anything but the most common purchases, except now we're stuck with s@&t customer service and no relationship with the proprietor.

Consider yourself lucky that you have a shop like that instead of an AdvanceAutoBoys with some kid behind the counter who wouldn't know the difference between a hose clamp and a hole in the ground.

</old man rant>

Yeah, the only line I crossed was when I went saw crazy the first night I had it. I also had that GS850 tailpiece and instantly thought I could easily make it fit on the 750 seat pan, not so much. So, I'll just have a 750 seat sitting on top of the frame not secured, ehh, it's not like I haven't rode other older bikes like that. I don't think my 71' CB500F seat was ever fastened.

This is definitely a project like non other I've had. When I was in the U.S. I was use to just splurging on parts I needed because I could I always make money, it's not so easy here for me.

[Chuck78]

Well, I decided not to be one of those guys so I'm going to do a thorough cleaning of the carburetors.

So, the plan is to clean up, then sand and paint the top of the triple tree, and back of the head light.

i've decided to post-pone the clip-ons, rear sets, and cafe seat mainly due to lack of funds. Hopefully by mid summer I will have a full time job and a running GS750 at least.

That's all excellent ideas, function first. You can take off parts later and refurbish or modify them, get the essential mechanical workings of the bike in solid condition now & RIDE IT! Then do other modifications step-by-step so you don't have a bike that is down and not writable during the bulk of the riding season. You can just peck away at small projects one at a time while the bike is still rideable, and do the projects so that you will only have the bike down for a weekend or a few evenings. Then rideable again.

Well, I decided not to be one of those guys so I'm going to do a thorough cleaning of the carburetors. I went to the nearest Mom and Pop shop, there are no peps and auto z's here, and explained to the guy my lack of knowledge on how to clean motorcycle carburetors in Sweden, as well as explained the dip conviently found in the states. He had me follow him to the back of the store to his office and showed me his brand new ultrasound cleaner, unused. So, I asked him how much it would be, he just smiled and said bring them by and will try it out together. Solid guy.

I'm on my way to the garage now, need to get some cleaning done to the garage, and I'm bringing a small table to put the disassembled carb on. I did get the bike to fire last time with the carbs on, no c clips, and two year old stabilized gas, however after put one liter of oil in it all came out the oil filter where the gasket was partially hanging out, my bad. Also, the #3 carb was leaking which they never did before.

So, the plan is to clean up, then sand and paint the top of the triple tree, and back of the head light.

i've decided to post-pone the clip-ons, rear sets, and cafe seat mainly due to lack of funds. Hopefully by mid summer I will have a full time job and a running GS750 at least.

I didn't realize crash bars were desireable? I took off the left one, there was no right.

The bike was definitely neglected, it was outside under a tarp when I bought it, but it did run and I rode it home.

I rode it it for almost a month and fell hard for the bike, then the cheap universal clutch cable broke. That started me trying to figure where to get OEM parts in Sweden and joining this forum. After reading and collecting information on here I had to get new intake runners, O-rings, and adjust the valves. It's become a long project but it's still rewarding.

I'm going to try and start it tonight, it takes 40mins on the tram to get to my garage so sometimes I need more motivation than just walking outside like I did in the U.S.

[Chuck78]

For your information, those are the original brakes, but someone went to great lengths to drill the rotor out. And that is the original swingarm, that someone went through all of the labor to chrome plate.

I'm always glad to see someone resurrecting these bikes, especially the neglected ones, rather than let them get more rare and see the neglected ones get parted out. Congratulations. If you were on my side of the ocean, I would be trying to buy this crash bars off of you!

IMG_0417.jpg

Got around to putting the side covers, cam cover, and exhaust on. The exhaust is so shiny it makes everything else look dirty.

Another strange I didn't notice till now, the V&H exhaust didn't come with a header collector-muffler connection, or I just lost it??

😁 maybe?

ill go down and get my bicycle and sometimes it works, other times it doesn't. It's probably an electrical problem.

Going to the garage now, will see how much I get done.

[chuck hahn]

So, was it the landlord shutting down the power at the bike room???

IMG_0412.JPG

And after

I also bought a new chrome v&h chrome exhaust, so once it's all together it should look nice and shiny.

I've been looking at a lot of pictures of cafe bikes and I feel like the blacked out look is over done even though it looks good. I like the looks of the brat seat but I don't want to do it on this bike even it would probably be easier. The biggest issue I can't decide on is the color. I originally thought 77' red but after lots of pictures of black and red bikes I think it looks generic for rattle can. I'm going in the direction of a dark blue, white, and maybe some red pin stripes but with an egg shell finish. I think the GT's in the 70s had this scheme and the GSX1400 naked bikes in Europe.