Search:

Type: Posts; User: Nessism; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.17 seconds.

  1. Robert Barr used to sell the washers...

    Robert Barr used to sell the washers...
  2. Replies
    11
    Views
    82

    The problem with used 40 year old master...

    The problem with used 40 year old master cylinders is there is often corrosion inside which causes pitting in the body rendering the master useless and not suitable for rebuilding.

    For a 650 you...
  3. Replies
    21
    Views
    236

    Honestly Argon, you are so far off track on this...

    Honestly Argon, you are so far off track on this I don't even know what to say.

    I worked for a couple of decades in the automotive business, in the quality side of the industry trying to help...
  4. Replies
    11
    Views
    82

    There is no baseline when the brake system is...

    There is no baseline when the brake system is full of sludge.

    As Rich stated: remove calipers, pop out the pistons, pull plunger out of mater cylinder, clean everything out and consider replacing...
  5. Replies
    24
    Views
    122

    Impressive job. Thanks for sharing. Keep...

    Impressive job. Thanks for sharing.

    Keep going...
  6. Seems like Redpocket. Dale turned me on to them...

    Seems like Redpocket. Dale turned me on to them a few years ago and I've been using them since. Good customer service. Pick whatever network you want.

    https://www.ebay.com/itm/133051277200
    ...
  7. Replies
    21
    Views
    236

    Sorry, but unless the grill advertised it's...

    Sorry, but unless the grill advertised it's ability to withstand direct rain with no ill effect I don't think you have a case. Put the grill under an overhang or get a cover would be my advice.
  8. Replies
    5
    Views
    110

    Building your own lines form made in USA Earl's...

    Building your own lines form made in USA Earl's parts removes all doubt regarding getting the exact perfect length and angles of the hose ends. It's cheaper than most all premade lines too.
  9. Oooo! Ouch!

    Oooo! Ouch!
  10. Replies
    8
    Views
    112

    Dyna S is path of least resistance. It works...

    Dyna S is path of least resistance. It works with the stock coils so no worry there.
  11. Replies
    8
    Views
    129

    The plug is tapered and wedges into the hole in...

    The plug is tapered and wedges into the hole in the carb body. You do NOT want the plug coming loose and falling into the carb throat where it will get sucked into the engine.
  12. Replies
    8
    Views
    129

    Buy used carb body and hacksaw it apart to...

    Buy used carb body and hacksaw it apart to extract the plug. That's the only way I know to get a plug, other than making one on a lathe.
  13. Replies
    32
    Views
    847

    Photos are tiny.:(

    Photos are tiny.:(
  14. Replies
    4
    Views
    69

    The answer can be found by looking at the wiring...

    The answer can be found by looking at the wiring diagram in the factory service manual or on Basscliff's website. You didn't mention what bike and year so there is that.
  15. Replies
    5
    Views
    96

    Did you wind up the tensioner spring and push in...

    Did you wind up the tensioner spring and push in the plunger before tightening the setscrew before reinstalling the tensioner? Then upon install, release the setscrew and snug down the nut? Reason...
  16. My guess is either vapor lock from a bad gas cap...

    My guess is either vapor lock from a bad gas cap or maybe a bad ignitor which malfunctions when hot. Sorry I can't be more definitive.
  17. Replies
    13
    Views
    204

    Agree. New wheel time. Bummer.

    Agree. New wheel time. Bummer.
  18. Replies
    4
    Views
    68

    Use the 100. 90 is too skinny

    Use the 100. 90 is too skinny
  19. Replies
    4
    Views
    214

    Amazing race today! So much fun to watch. I...

    Amazing race today! So much fun to watch. I don't want to give anything way for those planning to watch later but it was a real classic in my opinion.
  20. Replies
    7
    Views
    199

    Buy both, and more. Take a full inventory and...

    Buy both, and more. Take a full inventory and buy enough shims for your next couple adjustments. Most of the time you can shuffle shims to some extent so you should only need to buy half dozen...
  21. The wires can be replaced. You just need to get...

    The wires can be replaced. You just need to get them to release from the coil. Chip away any epoxy where the wire enters the coil and then stick a pin or pick tool between the wire and coil, going...
  22. I'd pull the wires out of the stock coils and...

    I'd pull the wires out of the stock coils and replace them, along with the plug caps. And points were great as long as they are properly maintained.
  23. Replies
    3
    Views
    150

    Do a google search on "oem Suzuki motorcycle...

    Do a google search on "oem Suzuki motorcycle parts." There are a large number of dealership sources with online parts fishe lookups. Partzilla.com is a good one. Once you find the part you click...
  24. Replies
    8
    Views
    268

    Error on the large clearance side. It's no...

    Error on the large clearance side. It's no problem running clearance up to .12mm. Tight on the other hand is NO GOOD.
  25. Replies
    12
    Views
    386

    If the bike has the original brake lines it's...

    If the bike has the original brake lines it's good to change them out because a scummy scale can form in the inside and flushing won't remove it, and this scale will contaminate the fluid, even if...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4