Search:

Type: Posts; User: Brendan W; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.27 seconds.

  1. Replies
    21
    Views
    236

    I have a sahara 350. It sits out in the summer...

    I have a sahara 350. It sits out in the summer rain and never has runoff from the sand grease trap.
    I don't cover it.
    Design defect?
  2. Replies
    19
    Views
    210

    I would open it up and clean it anyway. Most...

    I would open it up and clean it anyway. Most likely there is a lot of dirt in there.
    My meter is not top of the range and I am suspicious of it's resistance measurements.
    I would be more confident...
  3. At this rate they'll be paying us to use the...

    At this rate they'll be paying us to use the service.
    Payback for what they used charge back in the 90s :)
  4. Replies
    12
    Views
    188

    I saw it fine. Just had to say no and reject all...

    I saw it fine. Just had to say no and reject all and so forth. Looks really cool.
    Maybe it's a time zone day night thing?
  5. Replies
    19
    Views
    210

    I had almost the same voltages at the coil. I...

    I had almost the same voltages at the coil.
    I cleaned the fusebox, the ignition switch, the kill switch and the sneaky one was the coil supply plugs.
    That got me back to about half a volt below...
  6. What about fan belts?

    What about fan belts?
  7. Replies
    11
    Views
    169

    Gaia is probably thinking... Humans, my greatest...

    Gaia is probably thinking... Humans, my greatest mistake. Four less on the planet is a good start even if only for a short while :)
  8. Replies
    43
    Views
    1,864

    Reminds me of a conversation with a dealer when I...

    Reminds me of a conversation with a dealer when I bought a new Citroen BX in 1990.
    Why is there no tool kit ?
    They are so reliable you won't need it and so complicated it wouldn't be of any use...
  9. Replies
    4
    Views
    188

    Yep, there should be a three digit code on the...

    Yep, there should be a three digit code on the gas cap, ignition and seat lock.
    In my case the ignition was replaced and has a different key.
  10. That's a valid enough argument as long as the...

    That's a valid enough argument as long as the connections are good. Even if they aren't perfect how much difference can it make?
    For me the returns were above the airbox and out of sight with all...
  11. Replies
    22
    Views
    484

    I have a Yamaha NOS shim here somewhere which is...

    I have a Yamaha NOS shim here somewhere which is also 29mm.
  12. Replies
    12
    Views
    386

    I've had a PM or two with the OP. Anti dive is...

    I've had a PM or two with the OP.
    Anti dive is still on there and all original hoses.
    Never had anti dive. Could that be causing pressure lock?
  13. Have you tried marking the chain and rear...

    Have you tried marking the chain and rear sprocket to see if it's chain or wheel position doing it?
  14. To my way of thinking, the R/R is grounded...

    To my way of thinking, the R/R is grounded correctly when it is connected directly to the returning current flows. If the lights etc are grounded to the frame and the R/R to the frame you have the...
  15. Replies
    8
    Views
    268

    Have you got smaller than stock diameters on...

    Have you got smaller than stock diameters on there?
  16. Replies
    9
    Views
    167

    Wait for some future owner to come on here in...

    Wait for some future owner to come on here in fifty years looking for a part number :)
  17. Replies
    8
    Views
    268

    Just a thought but I you keep a record of what...

    Just a thought but I you keep a record of what shim thickness is where you can sometimes fix a clearance issue by swapping known shims.
  18. Replies
    12
    Views
    386

    That would point to an issue on top, either the...

    That would point to an issue on top, either the master cylinder, most likely, or the top hose internals developing a one way valve.
  19. Replies
    8
    Views
    268

    Do you know what shims are on each valve? A...

    Do you know what shims are on each valve?
    A simple swap could solve both exhausts if you are lucky.
    If it was just the .10 it would be safe enough to leave as is.
  20. Replies
    9
    Views
    167

    This true. Very often the act of writing down a...

    This true. Very often the act of writing down a problem causes a solution to appear :)
  21. Replies
    12
    Views
    386

    Are both disks heating up or just one side?

    Are both disks heating up or just one side?
  22. Replies
    4
    Views
    164

    Do us all a favour and say it next time and then...

    Do us all a favour and say it next time and then launch into a really long loud apology about your Tourettes. You won't have to put your hand in your pocket for the rest of the night :)

    There...
  23. Thread: Bad gas

    by Brendan W
    Replies
    10
    Views
    301

    Are we going to see brass dipsticks with water...

    Are we going to see brass dipsticks with water seeking paste and glass bowls with sampler taps?
  24. Replies
    14
    Views
    514

    Seen that once or twice. Someone had fitted a...

    Seen that once or twice. Someone had fitted a 40mm screw in place of a 35mm. The long screw seated against the cover but had bottomed out before squeezing the gasket. Another time someone had cut...
  25. Thread: Accident o

    by Brendan W
    Replies
    21
    Views
    583

    Best wishes for a speedy recovery. As Brian said,...

    Best wishes for a speedy recovery. As Brian said, focus on the best physio relationship. They generally know a trick or two and can help you push past what others might say will be the end point of...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4