Search:

Type: Posts; User: gs11ezrydr; Keyword(s):

Page 1 of 15 1 2 3 4

Search: Search took 0.08 seconds.

  1. OEM are probably the best for the money,for...

    OEM are probably the best for the money,for longevity,Even though they are way overpriced...But a company called FBG makes what I think is the closest to original and last depending on use, and are...
  2. Replies
    43
    Views
    2,168

    I could agree. Back in the early 80's at one time...

    I could agree. Back in the early 80's at one time we uncrated and assembled as many as seven 1100's in a day and there was a few that were faster and slower after break-in.A few customers complained...
  3. Replies
    3
    Views
    269

    Thanks for the info..I will get back at you if we...

    Thanks for the info..I will get back at you if we need any further assistance..parts etc...
  4. Replies
    3
    Views
    269

    New clutch baskets..

    So I went online to a couple parts houses and they show the O.E.M. clutch baskets for the GS1150's are no longer available..Is this fact or what ? I was hoping some of you all might know different .I...
  5. Most kits have a drill bit and a sheet metal...

    Most kits have a drill bit and a sheet metal screw to remove to mixture screw plug,Carefully drill a hole in the brass plug and screw the screw into the hole and pull it out..Some kits have another...
  6. I found a decent valve spring compressor for...

    I found a decent valve spring compressor for under 20$ on ebay for small engines.It goes from 16mm-30mm diameter springs..Works well on several different sized heads..
  7. Replies
    43
    Views
    2,168

    New..never been installed.. And thanks to all for...

    New..never been installed.. And thanks to all for the insight, I have a degree wheel,dial indicator,base and stand,piston stops,etc.I,m satisfied it's worth the time and money..I was just curious...
  8. Replies
    43
    Views
    2,168

    Cam Degreeing or not

    How important is it to degree a set of drop in Web Cams in a GS1150 .340 lift or even a set of .348 lift. Would it increase H.P. or just move the power band around..Thanks..I know Web recommends...
  9. Replies
    10
    Views
    559

    I believe the clearance is .001-.003 for 1100's...

    I believe the clearance is .001-.003 for 1100's and 1150's I have had to cut the center race also as you did. As far as shimming which I have done also. You can get them from Suzuki listed for 1150's...
  10. Replies
    41
    Views
    1,424

    Like in the other posts. Do yourself a favor and...

    Like in the other posts. Do yourself a favor and get an O.E.M. that should eliminate that as the problem,valve adj. could cause low vacuum also.The fuel tank needs to be vented as do the carb float...
  11. Replies
    18
    Views
    831

    I have tried the Maxi-X pipe years ago on a...

    I have tried the Maxi-X pipe years ago on a GS1100L model 7" slick and a bar. It provided more low end power and increased the 60' times but would not let the motor rev out through mid range and top...
  12. What is the condition of the battery? Was it...

    What is the condition of the battery? Was it fully charged before R/R was installed? Could effect charging output..Possibly trying to charge the battery instead of maintaining it.. 16VDC should be...
  13. Replies
    5
    Views
    356

    I remember back in the early eighty's we ran 4...

    I remember back in the early eighty's we ran 4 big bore dirt bike carbs in Pro Stock,Never seen these till now, Just about all of the dirt bikes ran hex jets back then,Thanks.
  14. Replies
    28
    Views
    657

    Thanks for all the info and...

    Thanks for all the info and opinions...Appreciated. As of now there is a 100$ basket case engine and a free ATV frame. Low if no budget...Just tossing ideas... Thanks again..
  15. Replies
    19
    Views
    812

    Just wondering that with CV carbs by just opening...

    Just wondering that with CV carbs by just opening the throttle plates all the way won't the slides still be some what of a restriction,causing lower #'s
  16. Replies
    28
    Views
    657

    Was just trying to minimize any wiring,Not so...

    Was just trying to minimize any wiring,Not so much concerned about weight, Just a theory,is there a possible H.P. gain with the stator not being energized and placing some amount of draw,or...
  17. Vapor Blast now you got me curious.Thank you.

    Vapor Blast now you got me curious.Thank you.
  18. Replies
    28
    Views
    657

    Be nice,if things go right,I will..I have about...

    Be nice,if things go right,I will..I have about 35 ATV frames to pick from...From a friend that wants to do it.Thinking of a 3 wheeler, GS front section and an ATV chain driven solid axle rear...
  19. Replies
    28
    Views
    657

    Thanks....Good thinking..

    Thanks....Good thinking..
  20. Replies
    28
    Views
    657

    Thank You. Exactly...Except separate starting and...

    Thank You. Exactly...Except separate starting and running systems.Minimal wires,3 switches Starting,Running,Fuel pump..
  21. Replies
    28
    Views
    657

    Yep even Top Fuel.in-line 4's and TF Harley...

    Yep even Top Fuel.in-line 4's and TF Harley motors.. Several categories,Stock,SS/Modified,Unlimited.. Search on You Tube and enjoy..ATV dirt drags should do it lol.
  22. Replies
    28
    Views
    657

    Consider It only has to run 200ft..And if it goes...

    Consider It only has to run 200ft..And if it goes rounds there will be a back up battery,ready to install.I think if I monitor the voltages for a while I might find a charging pattern..
  23. Replies
    28
    Views
    657

    Total loss ignition

    I was wanting to remove the charging system off of an engine.Total loss Ign. I know I will have to power the coils and the dyna S Ignition.I was planing on removing the stator itself and the...
  24. I was just hoping that there might be some...

    I was just hoping that there might be some "miracle" solution out there..For cleaning cases etc...Still am..I got this basket case motor (in good shape) just a few little gremlins..I am wanting to...
  25. What to use when cleaning cases that were in storage for a while

    I recently bought some 82 1100 cases.The paint outside is in good shape,I would like advice on what if any chemicals,rust removers,tape off and bead blasting,or old fashioned Scotch Brite and elbow...
Results 1 to 25 of 364
Page 1 of 15 1 2 3 4