Search:

Type: Posts; User: chuck hahn; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.94 seconds.

  1. Replies
    11,014
    Views
    544,056

    Put 140 miles in today. Bunch of us rode out...

    Put 140 miles in today. Bunch of us rode out route 66 to Arcadia OK.  Had burgers at POPS.
  2. Replies
    11,014
    Views
    544,056

    Put 140 miles in today. Bunch of us rode out...

    Put 140 miles in today. Bunch of us rode out route 66 to Arcadia OK. Had burgers at POPS. I was on the 83 KZ750 L3
  3. They werent soaked just sprayed. Carb spray will...

    They werent soaked just sprayed. Carb spray will shoot through real easy but NOT remove scale and super hardened gas shellac. all you did was fool yourself and now they need CLEANED properly. Dont...
  4. ok.....so youre problem is most likely still...

    ok.....so youre problem is most likely still dirty tiny passages in the carb bodies or way out of sync. i would try doing a very very careful bench sync first. set the top mixture screws at 1 1/2 out...
  5. I do rebuilds. Contact me via a PM should you...

    I do rebuilds. Contact me via a PM should you need me.
  6. STORE THIS PLACE. service manuals and carb...

    STORE THIS PLACE. service manuals and carb turtorials on right margin

    http://members.dslextreme.com/users/bikecliff/
  7. Bench sync them and vacuum gauge vsync them once...

    Bench sync them and vacuum gauge vsync them once running. do valve adjustments. check float hts per the service manual specs
  8. Replies
    48
    Views
    2,839

    Todays festivities included degreasing the entire...

    Todays festivities included degreasing the entire engine and painting the lower half. Then i turned my attention to getting the Neways busy and doing a valve job. Lapped all the valves and decided 6...
  9. I didnt see carbs synced mentioned. How about the...

    I didnt see carbs synced mentioned. How about the clutch basket bearings? Starter clutch bolts tight? It goes away around 2000 rpm you say?
  10. Replies
    48
    Views
    2,839

    Looks like tomorrow ill be able to get back after...

    Looks like tomorrow ill be able to get back after this bike. Plan is to start degreasing and prepping engine for paint. Been a long minute but i finally decided no more customers bikes till i have...
  11. Replies
    5
    Views
    134

    carb tutorials on right margin ...

    carb tutorials on right margin

    http://members.dslextreme.com/users/bikecliff/
  12. Thread: Chuck Hahn

    by chuck hahn
    Replies
    18
    Views
    1,239

    ill take some pics with the camera. Ones i sent...

    ill take some pics with the camera. Ones i sent Chris were with my phone as ive went along.
  13. Replies
    2
    Views
    162

    Bj thomas died

    Passed away today at 78. Loved his songs and voice. LEGEND
  14. Replies
    14
    Views
    503

    Octane means diddly squat for power added or...

    Octane means diddly squat for power added or power lost.

    What is octane rating? Octane rating is the measure of a fuel's ability to resist "knocking" or "pinging" during combustion, caused by the...
  15. Replies
    11
    Views
    405

    It goes on if i happen to be going into a...

    It goes on if i happen to be going into a mandatory wear state. Other than that , yes Trevor, it sets on the shelf.
  16. Replies
    31
    Views
    934

    So change to non resistor caps and the R wont...

    So change to non resistor caps and the R wont scare you. As you read directly from NGK there arent gonna be anymore B8ES once existing supply is sold out.

    Or use the other plug which is a non...
  17. Replies
    31
    Views
    934

    I have edited the original post with information...

    I have edited the original post with information about B8ES plugs being superceded....
  18. Replies
    31
    Views
    934

    Ngk plug shortahe

    Ive heard a lot about lack of plugs and some even claiming NGK is stopping making plugs.. Heres the skinny right from NGK......

    Thank you for your inquiry. Please do not believe people who are...
  19. Thread: Chuck Hahn

    by chuck hahn
    Replies
    18
    Views
    1,239

    I will roll the bike outside tomorrow and do a...

    I will roll the bike outside tomorrow and do a video without being inside the storage unit, I think that will be much better
  20. Thread: Chuck Hahn

    by chuck hahn
    Replies
    18
    Views
    1,239

    Got the XS1100 fired off today and synced the...

    Got the XS1100 fired off today and synced the carbs. Then switched gears to brakes. All the pistons front and back are heavily pitted so they will be rebuilt. I sent a video to Warrens son. Maybe...
  21. Replies
    11
    Views
    405

    New helmet paint

    Decided it was time to sand the old skull skid plate and lay out a new design. Had a buddy make me decals of the big four in Japanese font for a little accent. Ready for clear.

    SUZUKI ON THE...
  22. Replies
    17
    Views
    792

    There's no way I would put that back in my bike...

    There's no way I would put that back in my bike or anyone elses. Disaster waiting to happen. Copy the part number and paste it in the search box at ALPHA SPORTS. It will then give a list of all...
  23. Replies
    17
    Views
    792

    Replace it....................

    Replace it....................
  24. Replies
    8
    Views
    278

    Ones I got flexed at the tips and wouldn't...

    Ones I got flexed at the tips and wouldn't squeeze tight enough to release the clip from the groove. Post a pic of your please.
  25. Replies
    8
    Views
    278

    Circlip plier recommendations

    What brand and / or model of long each circlip pliers do you have and really like for EASY removal of master cylinder circlips?

    EDIT... in response to Eds post about motion pro. I spent 25 bucks...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4