Search:

Type: Posts; User: dennco2; Keyword(s):

Page 1 of 5 1 2 3 4

Search: Search took 0.41 seconds.

  1. I bought a used SH775 R&R but after receiving it...

    I bought a used SH775 R&R but after receiving it I realized the mounting holes don't match up to my 450. Looks like I will have to drill 1 or 2 new holes along with retaining nuts.

    Also, will...
  2. Replies
    41
    Views
    1,413

    I finally got out to my gs450 again to check the...

    I finally got out to my gs450 again to check the charging voltages and was surprised the numbers looked way better than the last time I checked. I did not get all the voltages ... but got 14.65 at...
  3. I wish I had such a full windscreen to use .......

    I wish I had such a full windscreen to use .... but the picture is of someone else's bike on the internet. Then again, I don't ride fast with the gs450 usually.
  4. I found an Amco brand back rest/luggage rack...

    I found an Amco brand back rest/luggage rack apparently designed for a xs650 Yamaha and it fit nicely on the front mount to the bike frame. But for the rear mounting, I had to fabricate 2 steel...
  5. A new starter motor relay solenoid has been...

    A new starter motor relay solenoid has been installed .... and performs fine. The old relay was unreliable and would stay in the ON position sometimes. Since pulling the magneto flywheel and...
  6. So you have a good used R&R to sell? If so, how...

    So you have a good used R&R to sell? If so, how much $?
  7. Shopping for a Shindengen R&R for my gs450

    I would like to upgrade to a Shindengen R&R for my gs450. In researching them, I see a couple different model numbers and wondered which one is correct for my bike? I see a SH775BA and a SH775AA. ...
  8. I have ordered another starter relay and it...

    I have ordered another starter relay and it should arrive next Saturday. By next Sunday, I hope to have this problem solved and will report back hopefully with good news.
  9. In a test ride a week ago or so, I could feel a...

    In a test ride a week ago or so, I could feel a drain in engine power and I believe the starter clutch was intermittently grabbing on to be driven direct drive by the engine. It would grab and...
  10. Okay, makes more sense to me now. I started the...

    Okay, makes more sense to me now. I started the engine today and all sounded normal at idle ... so a half hour later I took the bike out for a short ride. When starting the engine for that ride,...
  11. Yes, the starter relay solenoid must be hanging...

    Yes, the starter relay solenoid must be hanging up in the ON position. I don't understand how the starter motor would keep running after I turned OFF the ignition?? There was no stopping that thing...
  12. I put all parts back on the bike I had removed to...

    I put all parts back on the bike I had removed to pull the rotor flywheel and inspect the stator and starter clutch. I installed the charged battery and the engine started immediately. I kept the...
  13. What is the best source to get the SH775 part at...

    What is the best source to get the SH775 part at a good price? Any clones knockoffs to be aware of?
  14. I took a picture of the stator when it was off. ...

    I took a picture of the stator when it was off. Do you see anything abnormal in this pic? 62710
  15. So after finally popping off the rotor flywheel, ...

    So after finally popping off the rotor flywheel, I was able to inspect the stator windings and starter clutch parts. The stator coils looked quite dark indicating it has gotten very warm during it's...
  16. Finally had success popping off the rotor...

    Finally had success popping off the rotor flywheel off the tapered crank. It was very stubborn and we tried impact wrench, banging with a rubber mallet, a breaker bar. It finally gave up. Anyway, for...
  17. I ordered the puller bolt recommended above ......

    I ordered the puller bolt recommended above ... but it was too large. 14mm was the correct fit. First, I struggled to get the center 17mm mounting bolt off. With chain vice grips to hold the outside...
  18. What puller to remove the magneto flywheel on a gs450?

    The service manual says part 09930-30102 ... which is a sliding hammer type puller. People in this group have stated that type tool wasn't effective on their rotor covers and also not the 3 jaw...
  19. Replies
    41
    Views
    1,413

    With great advice offered here in this forum ......

    With great advice offered here in this forum ... I now have solved my starting problem, so will close this Topic thread. Now that it starts again, I NOW realize I have other issues which I will...
  20. Replies
    41
    Views
    1,413

    Yes, I have a lot of work to do to get this...

    Yes, I have a lot of work to do to get this running right. Against my better judgement, I took this bike out for a couple mile ride. I had the hanging rpm problem again but somewhat controlled by...
  21. Replies
    41
    Views
    1,413

    The GS450 was extremely hard to start and I used...

    The GS450 was extremely hard to start and I used up most of the bike battery trying to get it started. Then I jumped my Dodge Van battery to the bike battery and tried several crank attempts, till...
  22. Replies
    41
    Views
    1,413

    I was able to buy another used starter with the...

    I was able to buy another used starter with the same model number on Ebay. It definitely ran at a higher rpm with 12 volts ... than my old one. It definitely did not try to torque out of my hand when...
  23. Replies
    41
    Views
    1,413

    Yeah, I am convinced this one is near dead. ...

    Yeah, I am convinced this one is near dead. Good advice to give up on it. I hope I get lucky with another used one with full power.
  24. Replies
    41
    Views
    1,413

    UPDATE: I have delayed working on my starter...

    UPDATE: I have delayed working on my starter motor problem ... until yesterday. I pulled the starter motor out of the bike AGAIN ... so I could open it up and inspect. The armature commutator had a...
  25. With your advice, I looked up the correct tire...

    With your advice, I looked up the correct tire size at Suzuki Parts House and confirmed the tires sizes are correct. I couldn't make much sense of the numbers cast into the wheel. Anyway, I just...
Results 1 to 25 of 125
Page 1 of 5 1 2 3 4