Announcement

Collapse
No announcement yet.

Carb leaking fuel and idle too high

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Carb leaking fuel and idle too high

    Hi all

    I have a Suzuki GS450Ex 1981 with the Mikuni BS34 carbs. I have just cleaned them and got them on the bike and finally the bike starts and runs on its own fuel, not just the start gas like it did before. However the idle seems a little too high and I can't adjust it down no matter how much I adjust the idle screw. I guess the intake boots could be old? But I wonder as well, could it be that the air box needs to be replaced too? Does it matter that it seals correctly between the carb and air box or is it just important between the carb and the engine?

    Secondly the carb is leaking fuel from the T-line I suspect? Having a hard time finding a t-line that will fit the carbs and a company/seller that ships internationally (I'm in sweden). Any one got any good tips on where to look, preferably a link to an eBay item that they know fits. I can only find ones similar that are for the yamaha xs, will they fit, which models have the same carb?

    Thanks for any advice

    #2
    Suzuki still makes the fuel-T. It is listed on Bike Bandit, so you should be able to order it from a dealer or online parts dealer. They wanted $36.00 for it, but it's a part that is necessary. The seal between the carbs and air box are very important. Too much air will cause a lean condition and you will never be able to adjust them properly. Get those problems sorted out and that may cure the idle problem.
    Last edited by OldVet66; 12-31-2016, 12:15 PM.
    '78 GS1000E, Dyna-S ignition, Dyna Green Coils, K&N pods, Delkevic SS 4-1 exhaust, Dynojet Stage 3 jet kit, Russell SS Brake Lines, Progressive suspension, Compu-Fire series Regulator 55402 and Advmonster cree LED headlight conversion.

    Comment


      #3
      Make sure there is some slack in the throttle cable.

      Look where the cable attaches to the carbs. The inner cable should be loose when the throttle is closed.
      If it is tight, make an adjustment either at the top (next to the throttle grip) or at the bottom, where the cable attaches to the carbs.

      .
      sigpic
      mine: 2000 Honda GoldWing GL1500SE and 1980 GS850G'K' "Junior"
      hers: 1982 GS850GL - "Angel" and 1969 Suzuki T250 Scrambler
      #1 son: 1986 Yamaha Venture Royale 1300 and 1982 GS650GL "Rat Bagger"
      #2 son: 1980 GS1000G
      Family Portrait
      Siblings and Spouses
      Mom's first ride
      Want a copy of my valve adjust spreadsheet for your 2-valve per cylinder engine? Send me an e-mail request (not a PM)
      (Click on my username in the upper-left corner for e-mail info.)

      Comment


        #4
        Rubber O-rings on the intake boots are likely to be leaking unless you replaced them.

        Buy Suzuki 13685-44110 - NIPPLE. This OEM part is guaranteed by Suzuki's limited part warranty ✓ FREE Shipping on qualified orders - Partzilla.com
        Ed

        To measure is to know.

        Mikuni O-ring Kits For Sale...https://www.thegsresources.com/_foru...ts#post1703182

        Top Newbie Mistakes thread...http://www.thegsresources.com/_forum...d.php?t=171846

        Carb rebuild tutorial...https://gsarchive.bwringer.com/mtsac...d_Tutorial.pdf

        KZ750E Rebuild Thread...http://www.thegsresources.com/_forum...0-Resurrection

        Comment


          #5
          Thanks for the advice. I will replace the o-rings on the intake boots and give a closer look to the throttle cable. Hope that helps.

          Comment

          Working...
          X