Carb OEM specs as per factory manuals

[BassCliff]

Hi guys,

Just a reminder...

This is a specification thread.

If you have technical questions, start your own thread in the Technical Section. Take advantage of all the generous experts here.


Thank you for your indulgence,

BassCliff

[Colorado85gs550]

i think we now have all the models covered.


-ryan

We don't......

we still don't have specs for the 2 barrel siamesed carbs on the GS550E......

anyone?

[Griffin]

We don't......

we still don't have specs for the 2 barrel siamesed carbs on the GS550E......

anyone?

I have a factory service manual in the garage that has the specs for '83, '84, and '85. I'll try to post it here today sometime.

[Colorado85gs550]

thanks griffin!!

[Julia]

Can anyone please tell me what all this means? is the numbers like 0.7 mean the turns when adjusting? What do all these numbers mean? I'm used to dealing with fuel injection. Sorry

Julia


GS 650 GZ/GLZ (82)

idle r/min 1100-+/-100r/min
carb mik bs32ss (4 seprate carbs)
id no 34300
bore size 32 (1.26)
float height 22.4.+/-1.0 (0.88 +/-0.04)
fuel level 5.0+/-0.5 (0.20 +/-0.04)
main jet #110
main air jet 2.0
jet needle 5C45
needle jet Y-7
pilot jet #42.5
throttle valve #135
by pass 0.8, 0.7, 0.8
pilot outlet 0.7
valve seat 2.0
starter jet #45
pilot screw pre-set (1.5 turns back (mixture screw))
pilot air jet #160
throttle cable play 0.5-1.0 (0.02-0.04)
choke cable play 0.5-1.0 (0.02-0.04)

[Guest]

why exactly are you asking? getting the full answer would fill up pages...
if you're just fixing a bike, these are all the numbers you likely need to be concerned about:

float height 22.4.+/-1.0 (0.88 +/-0.04)
main jet #110
pilot jet #42.5
pilot screw pre-set (1.5 turns back (mixture screw))
pilot air jet #160

if you have standard intake and exhaust, just confirm that all the jet sizes are per specs, set the mixure screws and the float level as above and that's it.
refer to the carb rebuild pictorial for details on the respective jets, etc.

[cyclefvr2]

Anybody have them?--Can get my bike to run for a short time with starter fluid in the carb intake but wont rev or stay running

Thanks

Terry
WBL, MN

pilot jet is clogged, the little jet next to the floats,and main jet

[tlepac]

Sure was --but a 24 hr bath in Gunk cleaned them up nice and thanks to R Yonker I am running and synched and purring now! Thanks

Terry
WBL, MN

[Jesse002100]

1985 gs550 ????????

anyone have the specs for the 85 gs550/e
thanks

[cranemonkey]

I finally got around to typing up the specs for the 1980 GS850G carburetors.

1980 GS850GT Carburetor Specs
Unit of Measurement = mm(in.)

Carburetor type = Mikuni BS32SS
Bore Size = 32 (1.26)
I.D. No. = 45110
Idle rpm = 1050 +/- 100rpm
Fuel Level = 5.0 +/- 0.5 (0.20 +/- 0.02)
Float Height = 22.4 +/- 1.0 (0.88 +/- 0.04)
Main Jet = #115
Main Air Jet = 1.7
Jet Needle = 5D50
Needle Jet = X-5
Pilot Jet = #40
Bypass = 1.0, 0.8, 0.8
Pilot Outlet = 0.7
Valve Seat = 2.0
Starter Jet = #32.5
Pilot Screw = Preset
Throttle cable play = 0.5-1.0 (0.02-0.04)

Thank you for your indulgence,

BassCliff

Would it be dumb to ask if the 83 850 GL specs would be the same? Are they?

[Guest]

Would it be dumb to ask if the 83 850 GL specs would be the same? Are they?

it would not be dumb to ask
the specs should be the same

[Jesse002100]

anyone have the specs for the 85 gs550/e
thanks

still no help out there???

[KitKat]

Does any1 have the carbs specs, mainly the float and jet specs for an 82 gs 300L model Z if that helps


Thanks

[mriddle]

POST 109 of this thread.

Does any1 have the carbs specs, mainly the float and jet specs for an 82 gs 300L model Z if that helps


Thanks

[MacGyver]

anyone have the specs for the 85 gs550/e
thanks

Search is your friend:

http://www.thegsresources.com/_forum/showpost.php?p=292435&postcount=24

Your model should have these twined carburetors. I'll save you another search, the idle/preset screw is best to start at 3 turns out and adjust from there.