Bst36ss carbs 1200 motor tune

Collapse
X
Collapse
 
  • Page of 4
  • Time
  • Show
Clear All
new posts
Previous 1 2 3 4 template Next
  • yoshisakan
    #46
    Yeah I see that. I need to somehow find flanges with a 35degree turn down.

      Comment

      • GSX1000E
        #47
        And what happens when you switch 2 & 3 and 1 & 4 manifolds?

          Comment

          • yoshisakan
            #48
            Originally posted by GSX1000E
            And what happens when you switch 2 & 3 and 1 & 4 manifolds?
            Are you telling me to try this first? Worst case scenario, I'll scrap the stock ones and the nitrous flanges, buy some steel stock, make flanges, and weld 35 degree tube turn downs, drill/thread holes in them for the fuel and nitrous delivery, then get rubber boots to attach them to the carbs. That feels like the right thing to do anyway.
            Last edited by Guest; 01-16-2015, 11:16 AM.

              Comment

              • GSX1000E
                #49
                Do whatever it takes to level out those fuel bowls.

                  Comment

                  • Steve
                    GS Whisperer
                    • Jun 2005
                    • 35927
                    • southwest oHIo
                    #50
                    Originally posted by yoshisakan
                    Looking at Bandits though, there isn't a whole lot of difference in angle. It actually looks very minor. Take this one for example: [ATTACH=CONFIG]37903[/ATTACH]
                    "Not much difference"?? Really??







                    .
                    sigpic
                    mine: 2000 Honda GoldWing GL1500SE and 1980 GS850G'K' "Junior"
                    hers: 1982 GS850GL - "Angel" and 1969 Suzuki T250 Scrambler
                    #1 son: 1986 Yamaha Venture Royale 1300 and 1982 GS650GL "Rat Bagger"
                    #2 son: 1980 GS1000G
                    Family Portrait
                    Siblings and Spouses
                    Mom's first ride
                    Want a copy of my valve adjust spreadsheet for your 2-valve per cylinder engine? Send me an e-mail request (not a PM)
                    (Click on my username in the upper-left corner for e-mail info.)

                      Comment

                      • yoshisakan
                        #51
                        That picture illustrates it a bit better. Thank you Steve.

                          Comment

                          • rwnielsen
                            #52
                            A long time back guys were using radiator hose for intakes..... short sections.

                              Comment

                              • Guest
                                #53
                                The Gsxr/bandit carbs are designed to be tilted

                                  Comment

                                  • GSX1000E
                                    #54
                                    Originally posted by akckhim
                                    The Gsxr/bandit carbs are designed to be tilted

                                    Will be looking for that "I can't get these to work right" part in this thread soon...

                                      Comment

                                      • blowerbike
                                        Forum Guru
                                        GSResource Superstar
                                        • Aug 2008
                                        • 7057
                                        • Ohio Closer to KY Than Cleveland
                                        #55
                                        i hated these carbs on the GSXR's and bandits..
                                        on the other hand the 88-93 kat 1100 carbs and the 86-88 GSXR 1100 carbs are very user friendly.
                                        the above carbs require the same jet kit by the way...34mm vacuum flat slides.

                                          Comment

                                          • yoshisakan
                                            #56
                                            Is it safe to say that at the angle my carbs are at that the bike would be able to idle, but would stall when opening the throttle at all?

                                              Comment

                                              • yoshisakan
                                                #57
                                                Blowerbike - I believe those are actually 36mm's

                                                  Comment

                                                  • 78550GS
                                                    #58
                                                    Originally posted by yoshisakan
                                                    Blowerbike - I believe those are actually 36mm's
                                                    Stock carbs on an 88-93 Kat are 34mm cv's. BS34SS to be exact.

                                                      Comment

                                                      • Guest
                                                        #59
                                                        Short metal tops 34mm taller plastic tops 36mm some Canadian models got 38mm and wasn't there some 40mm?? This is my experience with them I could be wrong. If it idles but dies with any throttle sounds like too lean try it with a little choke pull. I'd say it has a massive air/vacuum leak or needles too low. ???

                                                          Comment

                                                          Previous 1 2 3 4 template Next
                                                          Working...