Starter solenoid suggestions needed.

[rustybronco]

Because of space limitations on my electrics panel, I'm considering a starter solenoid similar to this one, with the correct spacing (60mm), to possibly use in place of the stock unit.

http://www.ebay.com/itm/330600043684?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1423.l2649

Any known replacement suggestions that will fit the stock mounting with the studs facing outwards greatly appreciated.

[posplayr]

Because of space limitations on my electrics panel, I'm considering a starter solenoid similar to this one, with the correct spacing (60mm), to possibly use in place of the stock unit.

http://www.ebay.com/itm/330600043684?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1423.l2649

Any known replacement suggestions that will fit the stock mounting with the studs facing outwards greatly appreciated.

With a long enough bolt to fit through all the tabs with spacers, you could stack 2 side by side stacks of Bosch relays for 120/160 amps capacity.

If you really need the studs facing outward, put the screws in from the back and tighten to the mounting plate with nuts. 1 1/2" should do.

[rustybronco]

The way the original electrics panel components were mounted.



New panel with the SH775BA mounted in place of the separate regulator and rectifiers and the reason for needing a different solenoid.

[Nessism]

Hi Dale,

Fits this way...

[Guest]

I like these....http://www.texasindustrialelectric.c.../tyco_150A.pdf

[rustybronco]

Ed, unfortunately my fuse box is on the far right side.

[rustybronco]

Tried overlapping the fuse box with the R/R but it looks too crowded. I might be able to make a strap to move it to the left of the fuse box, but I may end up with the same problem if I do.



Nice idea showing me how yours was mounted. Might have to get me a 1980 electrics panel.

I like these....http://www.texasindustrialelectric.c.../tyco_150A.pdf

Nice neat solution if I can find one a little narrower.

[GSX1000E]

Why not just mount the RR Under the battery?

[posplayr]

Hi Dale,

Fits this way...

OK Ed,
A few questions:

1. Did you have to modify that side plate any to fit the SH-775?
2. Is that an OEM fusebox?
3. And finally what bike?

TIA Jim

[rustybronco]

Why not just mount the RR Under the battery?

Haven't checked to see if it would fit. I figured mounting it on the panel would be easier to get at it just in case I had to.

[Nessism]

OK Ed,
A few questions:

1. Did you have to modify that side plate any to fit the SH-775?
2. Is that an OEM fusebox?
3. And finally what bike?

TIA Jim

Plate is stock on my '80 1000S. Slotted the holes in the R/R ever so slightly so it could be slid away from the stock fuse box.

[posplayr]

Plate is stock on my '80 1000S. Slotted the holes in the R/R ever so slightly so it could be slid away from the stock fuse box.

Ed,

I know I have had some people that have wanted SSPB's for their Cooley's and I was not sure if the SSPB was a good fit after putting on the SH-775 on. It looks like the Fuse box and SH-775 are pretty close and the SSPB is an extra 0.1" wide ; close but probably not too close. Might have to open the holes just a tad more to slide the SH-775 more to the right but looks very doable and a nice fit.

It does look like the SH-775 would need relocation of the holes to be able to accommodate the OEM connector through; looks like it would interfere with the frame.

Jim

[rustybronco]

With a long enough bolt to fit through all the tabs with spacers, you could stack 2 side by side stacks of Bosch relays for 120/160 amps capacity.

Jim, thought about this for a bit. I have a few 40 amp relays at home. I may use one of them and convert the battery cables over to male spades.

We'll see.