Removal and installation of stator, and wiring

[timebombprod]

Have the stator case off and saw that the stator wire runs through the transmission case, do you have to take the case off to remove and install the stator?

Also gonna post a pic of my wiring I'm sure it's been ran through but I wanna know if its gonna need to be gone through or left alone, have a blue wire not connected to anything think it's part of my horn, only 1 of the 2 rear brake light wires are connected I mean it works but I dont know if that damages the wiring.

Just kinda a mess overall in my opinion I'm a bit OCD and if there was no harm in doing a rerouting and tuck to clean it up I wouldn't mind. If I were to I'd label all wires and there connections so I dont sit with a disassembled wiring harness or a mismatched one. If a few unplugged wires dont do any harm and I havent found anything electrical that doesn't work (which I havent) I'll just leave it alone

[cowboyup3371]

Remove the starter cover and you’ll see where they route

[Who Dat?]

Remove the starter cover and you’ll see where they route

The problem there is that to remove the starter cover, you may have to remove the carbs for enough room to get to the screws, unless you have some rather special tools.

[Rich82GS750TZ]

A 3/8"drive socket wrench (the small one) should allow you to get to the inner bolt that holds the starter cover down. It will only allow you very small movements of the handle, so it takes a while, but should be doable. Actually removing the starter motor, on the other hand, may prove to be impossible without dislocating the carbs out of their boots first. It's possible, depending on the size and shape of the connectors on the ends of the 3 stator wires, that you may have to cut them in order to thread them through the starter motor housing, especially if you try to do it without first removing the starter motor. It's tight in there.

[timebombprod]

Oh got confused thought it was the top of my transmission or something under that case.

Just so I'm on the same page as you guys it's this cover right?https://m.facebook.com/messages/atta...84826428326195

[Brendan W]

Oh got confused thought it was the top of my transmission or something under that case.

Just so I'm on the same page as you guys it's this cover right?https://m.facebook.com/messages/atta...84826428326195

Can't see it. Not a facebook user.

[Rich82GS750TZ]

I can't see the pics either, and I am on FB. If you haven't figured out how to post pics on the forum yet, I have instructions for using Imgur linked in my signature.

[timebombprod]

Nevermind it is the starter cover, I'm on track with yall now.

[Steve]

Can't see it. Not a facebook user.

I can't see it, either, but I'll change that to "Fakebook" or "Farcebook".

.

[Brendan W]

Nevermind it is the starter cover, I'm on track with yall now.

Bear in mind that the pole on the starter motor is potentially live.
Best practice would be to isolate the battery before going at it.

[Steve]

That pole should only be live when the starter button is pushed.

If the solenoid is stuck, it might be live, otherwise, it won't be.

But isolating the battery (remove a wire) is still good practice.

.

[Brendan W]

That pole should only be live when the starter button is pushed.

If the solenoid is stuck, it might be live, otherwise, it won't be.

But isolating the battery (remove a wire) is still good practice.

.

Call me paranoid but my cover has a 2mm hole burnt clean through.
I can only imagine the sequence of events that lead to that

[Steve]

Call me paranoid ...

Hi, Paranoid.

I noticed that my wife's bike was occasionally hard to start, occasionally smoking in the process.
Removed the cover, found a burnt spot on the bottom that had not (yet) made it all the way through.
I hammered a little more clearance and re-clocked the starter to avoid future incidents, but the principle remains, ... it's only hot when the starter button is pushed.

.

[Brendan W]

Hi, Paranoid.

I noticed that my wife's bike was occasionally hard to start, occasionally smoking in the process.
Removed the cover, found a burnt spot on the bottom that had not (yet) made it all the way through.
I hammered a little more clearance and re-clocked the starter to avoid future incidents, but the principle remains, ... it's only hot when the starter button is pushed.

.

You've been watching too much Gene Wilder and Marty Feldman
I think the starter was reassembled with the pole at 12 o'clock missing the blister completely.

[Steve]

I think hers was about 1:30, needs to be at 2:00.

.