Dynatek ignition

[timebombprod]

Which ignition do I put in my gs650? Looking at dynatek but if theres another brand give suggestions.

Pickups are taking a crap. That's the inconsistent skip, what's going on is the negative side is shorting out, sometimes it runs on two cylinders and the skip wont happen at all but once it's on all 4 that's when the skip starts happening.

Need one that fits a gs650

[timebombprod]

Will I need a TDC tool?

[tom203]

Have you tested the resistance of the two connector plug coming from signal generators? It?s just above battery....across the two pins you should see about 300 ohms (iirc). Unlikely to be this unless wires are shorting out. Your ignitor might be at fault..but this is also unlikely since you have a random misfiring.....

[timebombprod]

Have you tested the resistance of the two connector plug coming from signal generators? It?s just above battery....across the two pins you should see about 300 ohms (iirc). Unlikely to be this unless wires are shorting out. Your ignitor might be at fault..but this is also unlikely since you have a random misfiring.....

Blue and green wires? I only.checked for continuity which they do have but that was it.

I also used a testlight on them and both for some reason read negative.

Gonna check it still

[timebombprod]

Reads 332, is that too high to be usable?


Edit: guessing that it's not, seen a post and 360 is where the resistance can go to.

[timebombprod]

Screenshot_20210402-180252_Gallery.jpg


What is this red piece for? Pretty sure it's some sort of ground.

Can it be removed with the installation of the dyna S or does it need to be left on?

Gets in the way of the plate causing it to sit lopsided, didnt want to leave it like that.

[timebombprod]

[ATTACH=CONFIG]62659[/ATTACH]


What is this red piece for? Pretty sure it's some sort of ground.

Can it be removed with the installation of the dyna S or does it need to be left on?

Gets in the way of the plate causing it to sit lopsided, didnt want to leave it like that.

Cant find it on the signal generator section of any parts seller, weird.

[Rich82GS750TZ]

Looks like an oil pressure sensor/switch, but I don’t see it on the signal generator fiche either. Look at some of the other pages.

it’s hiding on the crankcase fiche. #38
https://www.partshark.com/oemparts/a...daed/crankcase

[timebombprod]

Looks like an oil pressure sensor/switch, but I don’t see it on the signal generator fiche either. Look at some of the other pages.

it’s hiding on the crankcase fiche. #38
https://www.partshark.com/oemparts/a...daed/crankcase

The signal generator itself had an extra wire going to it, but that makes sense being an oil pressure sensor

[Rich82GS750TZ]

The end of the red oil pressure switch should have a wire with a lug terminal screwed into the hole in the end of it. Wire probably green w/yellow stripe.

[timebombprod]

The end of the red oil pressure switch should have a wire with a lug terminal screwed into the hole in the end of it. Wire probably green w/yellow stripe.

Yes it did that was exact wire colour.

So probably should just use an OEM if I want the light.

[Rich82GS750TZ]

Yes it did that was exact wire colour.

So probably should just use an OEM if I want the light.

Yes, that’s what I would do.

[tom203]

If you want to use the dyna on a gs650 (or 450) ,you need to make a half moon cutout in dyna plate to clear oil sender.E59C1A7F-4AD8-4F8C-AED0-A70DFE619C6E.jpg

[timebombprod]

Wish it could hook up to the CDI plug instead of straight to coilpacks

[timebombprod]

Wish it could hook up to the CDI plug instead of straight to coilpacks

Realised CDI gets deleted, now know a better way to hook up the dyna