Help with mystery shouldered spacer

[PhillyKID53]

Hello all. I've been putting a lot of work in on my GS550 to get it road ready, and after a short stint out of duty from a bad flat, finally got a quick ride in. While pulling into my driveway and shutting down, I heard this part fall on the ground. After some forum digging and checking my manual/babbits, I'm coming up flat. I gather it's a spacer, but what exactly am I looking at here?

Gallery and dimensions in album, thanks all in advance.

http://imgur.com/gallery/PLOSvma

[hillsy]

It doesn't look like anything from the bike to be honest - if I had to guess I would say it looks like a modified spacer for one of the engine mount bolts?

Like #25 in this image cut in half?:

[Guest]

Front flat or rear??? What was your axle diameter??? Looks possibly like a wheel spacer, but I can't imagine you properly getting yer wheel back tightened down without it in place...

[PhillyKID53]

Engine was my first once over, it's all buttoned up right per the manual. The patina, machine pattern and general wear are really pushing me to believe it's from the bike. Might just be going crazy here, but not a fan of spare parts after a rebuild . I'll keep looking around.

[PhillyKID53]

Rear wheel, and the spacer stack up checks out with the manual there too, no real play to speak of. Changed to bearings with the tire so I triple-checked that guy. It's only 12mm ID, and OD is like a nickel maybe in size? I can get better info/pictures after work.

[Gorminrider]

Doesn't lleap to mind yet as anything I have on my bikes except a wheel axle bushing through the rubber seal and it seems small for that and it would be polished by a spinning rubber seal ...but does look like something that goes through a rubber seal....

possibly up under the gauges as a bushing through rubber... Gas tank mount ? bushing for bolt through the rubber grommet at back? A bushing for a headlamp mount..? though mine (gs650,gsx400) have no shoulders and are much thinner bushings...

[Grimly]

Possibly some joker picked up a piece of auto debris and left it on top of your crankcase, to rattle and fall off, giving you the worries.

[Cipher]

It looks like a suspension bushing
Threads have marked the bore
So it been getting loaded up

What years this thing

[PhillyKID53]

It looks like a suspension bushing
Threads have marked the bore
So it been getting loaded up

What years this thing

Think it's too small for any suspension parts, but does look just like one. It's a 1980, but probably a third of it is non original by this point.

[PhillyKID53]

Doesn't lleap to mind yet as anything I have on my bikes except a wheel axle bushing through the rubber seal and it seems small for that and it would be polished by a spinning rubber seal ...but does look like something that goes through a rubber seal....

possibly up under the gauges as a bushing through rubber... Gas tank mount ? bushing for bolt through the rubber grommet at back? A bushing for a headlamp mount..? though mine (gs650,gsx400) have no shoulders and are much thinner bushings...

Huh... I did tear the front end apart recently. And it looks like I'll be doing it again come Monday to be certain. Thanks for the angle Gorminrider.

[Guest]

Does your rear wheel have a rubber cushion and separate sprocket carrier? Looks a little like the bushing that goes thru the sprocket carrier bearing on some models, like my GS1100e...

[PhillyKID53]

So I checked the clocks, electrical mounts, wheels and anything else that would generally merit offsetting a bolt...
Nada. Certainly unsatisfying as far as answers go, but I'm electing to consider this closed for now. Not worth the extra stress and down time at the moment. If/when anything comes of it, I'll make sure to follow up. Cheers all.

[Gorminrider]

Good plan. Possibly flung from a vehicle ahead and trapped on your bike anyways. But keep it until you forget why.