Announcement

Collapse
No announcement yet.

Runs well but....

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Runs well but....

    Hi guys,

    Need a little help here. I've posted in the past and have received great advice so here I am again. Still a newbie though, in regards to mechanics.

    I have a GS1000ET and it's running well but at very hi revs I get black smoke. If in neutral and I rev it high the black smoke comes and it begins to stall out but give a little gas and it's back to idling smoothly. Someone at a red light thought my choke was on but it was not. I also want to point out that the exhaust is VERY stinky. After a ride I smell like a gas refinery. Not that I know what they smell like but I’m sure you get my drift. The plugs look like they’re on the dark side – sooty – but that can’t be why the exhaust is so bad. Any ideas to trouble shoot? Mechanic cleaned the carbs and jetted a couple seasons ago.

    Thanks in advance for the help.

    Gerry

    #2
    I would suspect that you have too large of main jets. Check your plugs at high rpm and see what color they are.

    Comment


      #3
      Do a search for "throttle chop" and jet your bike properly.


      Follow steps in order....First, dial in:
      • 1. Top end (full throttle / 7.5k to redline -
        Best Main Jet must be selected before starting step 2 (needle height)!
        • To get the best, most even top end power (full throttle/after 7500 rpm), select the main jet that produces the hardest pull at high rpm.
          • If the bike pulls harder at high rpm when cold and less hard when fully warmed up, the main jet is too large. Install a smaller main jet and retest until you find the main jet that pulls the hardest at high rpm when fully warmed up. This must be done first - before moving on to the other tuning ranges.
          • If the bike doesn't pull well at high rpm when cold and gets only slightly better when fully warmed up, the main jet is too small.
            • In order to properly tune the midrange and low rpm carburetion, THE MAIN JET MUST FIRST BE PROPERLY SELECTED after 10 to 15 minutes of hard use!
              • Do not pay too much attention to the low-end richness when you are changing main jets - you still need to be using the main jets that produce the best power at high rpm. You will deal with the low-end / cruise later - after step 2.
      • 2. Midrange (full throttle /5k-7k)
        Step 1 (Best Main Jet) must be selected before starting step 2!
          • Select best needle clip position
        • To get the best power at full throttle / 5k-7k rpm, adjust the needle height, after you have already selected the best main jet.
          • If the engine pulls better or is smoother at full throttle/5k-7k in a full throttle roll-on starting at <3k when cool but soft and/or rough when at full operating temperature, it is too rich in the midrange and the needle should be lowered.
          • If the engine pulls better when fully warmed up but still not great between 5k-7k, try raising the needle to richen 5k-7k.
          • If the engine pulls equally well between 5k-7k when cooler as compared to fully warmed up, the needle height is probably properly set.
            • Do not pay too much attention to the low-end richness when you are changing needle clip positions - you still need to be using the clip position that produces the best full throttle / 5k-7k power in conjunction with the main jets (Step 1) that produce the best power at high rpm. You will deal with the low-end / cruise next.
      • 3. Low end (full throttle / 2k-3k)
        Step 1 (Best Main Jet) and Step 2 (needle height) must be selected before starting step 3!
          • Float height (AKA fuel level & how to..)
        • To get best low-end power, set float height (fuel level) so that the engine will accept full throttle, without missing or stumbling, in 2nd gear from 2.5k to 3k rpm at minimum.
          • Float heights, unless otherwise specified in the installation guide, are measured from the "gasket surface" of the carb body to the highest part of the top of the float - with the float tang touching but not compressing the float valve spring.
          • If the engine has a "wet" rhythmic, soggy area at full throttle / 3k-4k rpm, that gets worse as the engine heats up, lower the fuel level by resetting the float height 1mm greater (if the original was 13mm - go to 14mm). This will lower the fuel level, making full throttle / 2k-3k rpm leaner.
          • If the engine is "dry" and flat between 2k to 3k rpm, raise the fuel level.
          • Example: change float height from 15mm to 14mm to richen up that area.
          • REMEMBER, since the main jet WILL affect low speed operation, the MAIN JET has to be within 1 or 2 sizes of correct before final float setting.
            • Warning: If the engine is left with the fuel level too high,, the engine may foul plugs on the street and will be "soft" and boggy at part throttle operation. Adjust Floats to raise/ lower the Fuel Level.
              • Base settings are usually given if a particular application has a history of fuel level criticalness. The Fuel level height in the float bowl affects full throttle/low rpm and, also, richness or leanness at cruise/low rpm.
            • Reference: a bike that runs cleanly at small throttle openings when cold, but starts to show signs of richness as it heats up to full operating temperature, will usually be leaned out enough to be correct if the fuel level is LOWERED 1mm. Check out and RESET all: Suzuki (all), Yamaha (all) and Kawasaki (if low speed problems occur). Needless to say, FUEL LEVEL IS EXTREMELY IMPORTANT!!!
          • If there are low-end richness problems, even after lowering the fuel level much more than 1.5mm from our initial settings, check for needle wear and needle jet (part of the emulsion tube). See Worn Needle and Worn Needle Jet diagram. It is VERY common for the brass needle jets (in the top of the "emulsion tube") in 36mm, 38mm and 40mm Mikuni CV carbs to wear out in as little as 5,000 miles. Check them for "oblong" wear - the needle jet orifice starts out round! Factory Pro produces stock replacement needle jets / emulsion tubes for 36mm and 38mm Mikuni carbs. Click here
      • 4. Idle and low rpm cruise
          • Fuel Screw setting (AKA mixture screws)
            • There is usually a machined brass or aluminum cap over the fuel screws on all but newer Honda. It's about the diameter of a pencil. Cap removal details. Newer Honda carbs have no caps, but use a special "D" shaped driver, usually supplied in the carb recal kit. We do have them available separately, too. 800 869-0497 to order -
          • Set for smoothest idle and 2nd gear, 4k rpm, steady state cruise operation. Set mixture screws at recommended settings, as a starting point. For smoothest idle, 2nd gear 4000 rpm steady state cruise , and 1/8 throttle high rpm operation. (pj tuning information)
          • Pilot fuel mixture screw settings, float level (but, you've "fixed" the fuel level in Step 3 - which you have already done!) AND pilot jet size are the primary sources of mixture delivery during 4000 rpm steady state cruise operation.
            • If lean surging is encountered, richen mixture screws (turn out) in 1/2 turn increments. Alternative pilot jets are supplied when normally required.
            • Pilot fuel mixture screw settings, float level and pilot jet size also affect high-rpm, 0 to 1/8 throttle maneuvers. Too lean, will cause surging problems when the engine is operated at high rpm at small throttle openings! Opening the mixture screws and/or increasing pilot jet size will usually cure the problem.
              • NOTE: A rich problem gets worse as the engine heats up.
                • If the throttle is lightly "blipped" at idle, and the rpm drops below the set idle speed, then rises up to the set idle speed, the low speed mixture screws are probably set too rich: try 1/2 turn in, to lean the idle mixture.
              • NOTE: A lean problem gets better as the engine heats up.
                • If the throttle is lightly "blipped" at idle, and the rpm "hangs up" before dropping to the set idle speed, and there are no intake leaks and the idle speed is set at less than 1000 rpm, the mixture screws are probably too lean: try 1/2 turn out, to richen mixture. Be sure there are no intake leaks and the idle speed is set at less than 1000 rpm!
      Also do a compression check and check your valve clearance before jetting.
      1983 GS 1100E w/ 1230 kit, .340 lift Web Cams, Ape heavy duty valve springs, 83 1100 head with 1.5mm oversized SS intake valves, 1150 crank, Vance and Hines 1150 SuperHub, Star Racing high volume oil pump gears, 36mm carebs Dynojet stage 3 jet kit, Posplayr's SSPB, Progressive rear shocks and fork springs, Dyna 2000, Dynatek green coils and Vance & Hines 4-1 exhaust.
      1985 GS1150ES stock with 85 Red E bodywork.

      Comment


        #4
        I would also verify petcock wasn't running raw fuel into cyl 2.
        Last edited by Guest; 04-17-2007, 05:55 AM. Reason: wrong cyl listed.

        Comment


          #5
          Thanks for the replies guys, I'll see what I can do on this end.

          Comment


            #6
            Originally posted by arveejay View Post
            I would also verify petcock wasn't running raw fuel into cyl 2.
            Ditto. I'd check the petcock first before the headache jetting. Pull off the vacuum line from the petcock and see if there is gas in it. This could be a really easy fix.
            1983 GS 1100E w/ 1230 kit, .340 lift Web Cams, Ape heavy duty valve springs, 83 1100 head with 1.5mm oversized SS intake valves, 1150 crank, Vance and Hines 1150 SuperHub, Star Racing high volume oil pump gears, 36mm carebs Dynojet stage 3 jet kit, Posplayr's SSPB, Progressive rear shocks and fork springs, Dyna 2000, Dynatek green coils and Vance & Hines 4-1 exhaust.
            1985 GS1150ES stock with 85 Red E bodywork.

            Comment


              #7
              hey just thowing this out there... i would deffently check the petcock first but if the choke is stuck maybe not in the line but in the carb wouldn't that pull to much gas....just a thought...please correct me if i'm way off.

              Comment


                #8
                Originally posted by chef1366 View Post
                Ditto. I'd check the petcock first before the headache jetting. Pull off the vacuum line from the petcock and see if there is gas in it. This could be a really easy fix.
                So if there is gas in the vacuum line, what is the easy fix?

                Comment


                  #9
                  Originally posted by gs1000 beauty View Post
                  So if there is gas in the vacuum line, what is the easy fix?
                  Petcock rebuild.

                  Comment

                  Working...
                  X