When I let the clutch out it stalls
Collapse
X
-
midnightkingkorin
When I let the clutch out it stalls
Please someone help me Ive just striped and cleaned the carbys(twice)and still whenever I let the cluch out no matter what revs it stalls.The clutch seems to be engaging ect.The carbys have been set by the book and tuned and floats set as per manual.
Tags: None -
terbang -
UncleMike -
midnightkingkorin
more info
Ive tryed to take of in first and second it is a GS1000 82 model Ive tryed the clutch adjustment and as for the switch Ill have to take a look at that but Im shure thats disconected.Ive recentley done a top end rebuild and everything was fine for about a week.It also is fitted with a side car and leading link front end.Comment
-
Planecrazy
Ok ... here's a dumb question: "Are you letting the motor warm up before pulling away? Both of my GS's will stall under load until they completely warm up (no LESS than five minutes running). If I MUST pull out immediately I have to keep the motor almost completely choked and keep the revs high in order to prevent a stall. After several minutes warming up the bikes both perform normally.
Good Luck!Comment
-
UncleMike
Steve, that sounds like you've got something up with your bikes. With all my GS's, once I went through the carbs, valves, etc., they required about 1/2-3/4 choke for about twenty seconds, and then would be fine.Comment
-
Planecrazy
Perhaps, Mike, but so far I've met a LOT of other GS owners who's startup routine is identical to mine (and their bikes, like mine, run perfectly after warming up for a few minutes). I figured it was just inherent in the design that the motor needed a few minutes to warm up. In all the years I had my 550L professionally maintained by a dealer as well as the times I did it myself the result has always been exactly the same - very consistent. Since the 1100G behaves exactly the same way I've never had cause to believe I could adjust away what appears to be a normal warm up sequence...
Regards,Comment
-
UncleMike
Weird. But I'm certainly not going to complain about my warm-up procedure. It's choke as long as it takes me to secure my helmet, even in cold weather, and the plugs are tan, tan, tan.Comment
-
Planecrazy
Glad it is so seamless for you! I guess I'll have to investigate whether the same is possible for me. :-D
Comment
-
nabrams
Comment
-
40-50 degree weather 3/4 choke runs up to 3k rpm's open choke till 1.5k rpm's put on helmet and gloves leave driveway about 1 mile away (3-4 mins) open choke completely (idles a little low) it's fully warm and idles @ 1.1k rpm's somewhere about 5-7 min's, the warmer it gets the quicker to get off the choke. it's been that way for the 2 years i've owned it and it's the nature of my beast.Perhaps, Mike, but so far I've met a LOT of other GS owners who's startup routine is identical to mine (and their bikes, like mine, run perfectly after warming up for a few minutes). I figured it was just inherent in the design that the motor needed a few minutes to warm up. In all the years I had my 550L professionally maintained by a dealer as well as the times I did it myself the result has always been exactly the same - very consistent. Since the 1100G behaves exactly the same way I've never had cause to believe I could adjust away what appears to be a normal warm up sequence...
Regards,Comment
-
t3rmin
Comment
-
Planecrazy
That sounds almost exactly the way both of my GS's have always behaved, regardless of whether they were freshly tuned or in need of a tuneup...40-50 degree weather 3/4 choke runs up to 3k rpm's open choke till 1.5k rpm's put on helmet and gloves leave driveway about 1 mile away (3-4 mins) open choke completely (idles a little low) it's fully warm and idles @ 1.1k rpm's somewhere about 5-7 min's, the warmer it gets the quicker to get off the choke. it's been that way for the 2 years i've owned it and it's the nature of my beast.
Regards,Comment
Comment