Broke Piece From Carb

[Monty]

I've been lurking this forum for about a month, it's really been helpful.

Question: Do you all have any advice for re-attaching a piece that broke off the Carb body?

While removing the Carb Float Pin during a rebuild yesterday, I broke one of the towers on the carb body that holds the float pin. See attached, I pointed at it with a red arrow.

Is there any type of epoxy that can hold the piece back on the to carb? There's not too much direct force on this area of the carb, but there?s going to be a ton of vibration and it will be submersed in fuel.

Thanks!!

[doctorgonzo]

Search for "broken float post", some have had success with JB Weld, some with epoxys, good fix using a brass tube slid over the post, or look for a spare set of carbs and swap that body.

[buckeyemike]

I used brass two a week or two ago seemed ok. we will see with time. And tried the aluminum weld rods they have now. That did not stick to good but I think rod should be good enough. I am just going to look for a spare in the future.

[doctorgonzo]

I used brass two a week or two ago seemed ok. we will see with time. And tried the aluminum weld rods they have now. That did not stick to good but I think rod should be good enough. I am just going to look for a spare in the future.

That's what I did. Ran it rigged for a couple months, then just swapped the whole body.

[Guest]

What size carb (bike model) and which carb. I might have an extra carb body.

[Monty]

It's the number 3 carb on a GS550 1980.

Sounds like JB Weld will work from the forums.

Thanks again!

[Loose Seal]

I had the same problem and ended up replacing the body, but after reading many threads on the subject, it is crucial to thoroughly clean/dry the piece and let the epoxy set for at least 24 hours before reassembling.

Also heard that plumber's epoxy putty works well too. It has gasoline tanks listed on the tube for suggested uses.

Good luck!

[Monty]

Yep, I'm in process of rebuilding the carb to it's pretty clean. I've read that acetone should be used to clean the area before using JB Weld. Will the regular carb cleaner spray do the same thing?

[salty_monk]

JB weld is not a good solution.. I also have a broken post on a 550 I just got, it wouldn't run... when I took the carbs apart the JB welded float post was just flapping around in the float bowl.

I would insert a pin between the two pieces, interference fit (at least that's what I am going to try anyway.

Dan

[doctorgonzo]

JB weld is not a good solution.. I also have a broken post on a 550 I just got, it wouldn't run... when I took the carbs apart the JB welded float post was just flapping around in the float bowl.

I would insert a pin between the two pieces, interference fit (at least that's what I am going to try anyway.

Dan

JB Weld failed for me as well, but there are things I might have done to improve it's chances. Still I consider that a "I need to really fix it ASAP" kind of solution.

[Zook]

Short of replacing the carb, welding it works. I took mine to a local weld shop and had it welded...for about the price of one used carb!

[doctorgonzo]

Short of replacing the carb, welding it works. I took mine to a local weld shop and had it welded...for about the price of one used carb!

Have to use TIG right?

[rustybronco]

I would insert a pin between the two pieces, interference fit (at least that's what I am going to try anyway.

Dan

Pin them together, it will work.

http://www.thegsresources.com/_forum/showpost.php?p=475224&postcount=7

http://i32.photobucket.com/albums/d44/rustybronco/pictures078.jpg