It lives

My eyes!
That was terriblely funny
Glad to see you made it through this thread!

Wait, that was a real movie?? I kept waiting for the chick to show up and the two dudes to start railing her in classic porno style... Then when that didnt happen I started to think someone posted a male on male porno... and THEN the chick showed up, so I thought ok, here we go.. but no.. That was AWFUL... didnt the producers of this crap realize, hey, this is awful?? Probably not. They were probably all jacked up on coke and thought it was the best thing ever.. Though i gotta admit, the "being hung by your eye socket from a crane" bit was pretty cool... And, im sorry, but if I get in a fight that results in my eye ball hanging on a rusty nail in the wall.. Im done, good fight, i gotta see the ER doctor now..

[chef1366]

This is really the worst fight scene of all time (or if not, it's damn close):

http://www.youtube.com/watch?v=uxkr4wS7XqY

My eyes!
That was terriblely funny
Glad to see you made it through this thread!

And yet... one of my favorite movie lines of all time.

Heh.



(This message brought to you by StevieD... forgot who's account I was logged on to!)

This is really the worst fight scene of all time (or if not, it's damn close):

http://www.youtube.com/watch?v=uxkr4wS7XqY

Yeah, it's pretty much either a drag race only or street race short run deal. I did do a 1327 1150 block for a guy in Hawaii that rode on the street but it would run warm in traffic! Ray.

YIKES do ya think it got hot.

[rapidray]

Yeah, it's pretty much either a drag race only or street race short run deal. I did do a 1327 1150 block for a guy in Hawaii that rode on the street but it would run warm in traffic! Ray.

That block gets almost to thin after that though

[rapidray]

Kris, you can sleeve a stock 1150 block to 1260 or 1327 both. Same sleeve for both, just over bore for the 1327. APE P/N for the sleeve is KA773. Ray.

After you blow this one up...you can put in bigger sleeves

NOPE! thats as big as it gets for a 1150 cylinder. You have to get a monster block after that.

[salty_monk]

Bah... looks like crap & I bet it will be really really slow*

Bill doesn't use the throttle anyway*

I plan on doing this to the ED motor. This is my street motor and I don't plan on doing anymore to it.

After you blow this one up...you can put in bigger sleeves

damn,
i thought only billy vose and tommy steadman painted there chassis that shade of blue
also,
that looks like elvis standing behind the turbo bike
ahhh,
i can smell the desert air once again

ELVIS??? has left the building,the only thing I can smell in my shop is case paint. Everybody who has raced the "BLUE" bike knows what to expect when you come up against it a AZZ WHOOPIN hahahahahahahahahaha.

[Charlie G]

Chef,

It's lookin good. I've been eyeing a blue 1100 in town. I may have caught the sickness.

cg

[chef1366]

I use copper gaskets & if they are put together correct, they don't leak! The head on my dragbike motor has been on since 2004 & still no leaks! Looking good Bill but I have a question for you. If you were paying to have the upper case half bored, why didn't you have it bored to clear 1327 or 1400 sleeves? It would've cost the same but if you decide to go bigger later you will have to pay to have it done again. I ask just because I'm curious. It would have no detrimental effects on the motor if the upper case were bored bigger than needed. When I have any bored, I have them done to 1428 sleeve diameter unless I am going 1500 or bigger. Keep up the good work & remain PATIENT!!! Ray.

I plan on doing this to the ED motor. This is my street motor and I don't plan on doing anymore to it.
Yeah right

[rapidray]

If I didn't have stock sleeves or had high compression pistons I'd o-ring.
Shoot I'm using copper gaskets. It will leak a little. Oil that is.

I use copper gaskets & if they are put together correct, they don't leak! The head on my dragbike motor has been on since 2004 & still no leaks! Looking good Bill but I have a question for you. If you were paying to have the upper case half bored, why didn't you have it bored to clear 1327 or 1400 sleeves? It would've cost the same but if you decide to go bigger later you will have to pay to have it done again. I ask just because I'm curious. It would have no detrimental effects on the motor if the upper case were bored bigger than needed. When I have any bored, I have them done to 1428 sleeve diameter unless I am going 1500 or bigger. Keep up the good work & remain PATIENT!!! Ray.

Are you using the same 0.340 cams? What are you going to degree them at. I thought i read you were gonna go 105/107.
Thats what I have mine at now and whoever said pods and 4-1 dont make torque is dead wrong, mine has TONS of bottom end and mid. My .340 web cams should be arriving this week and i am debating where to degree mine at. Any input from the experts? Sorry if its a bit of a highjack, Bill