swing arm for a 78 gs 1000

[Guest]

they sure do look KOOL...... I have considered it myself.

[Anonymous]

i really like the look of a stretched swing arm, and i would like to run it at the track sometime. so a swing arm of a 1100 or 1150 will fit a wider tire but the brake and sprocket have to be moved out. and how wide is tire compared to one on a new sport bike.

[80gs1000e]

1150 swingarm will not work, its a monoshock like they said earlier in the post. Unless you want to convert to a mono setup, major surgery and mods are needed to the frame and stuff......

An extended 1100 swingarm is going to be expensive IF you can find one. Thats a big IF. KZ swingarm might work also. Or get an 1100 stock arm and have it made longer....still lots of $$$ and what little cornering you had is worse off.

Does your bike have any other mods already? Engine mods?

[Guest]

it's a lot easier to make the 1150 swingarm into a twin shock arm than make a twin shock bike into a monoshock one.

older gsxr 1100 arms are a couple inches longer than the gs's...

[80gs1000e]

http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&rd=1&item=4529625467&category=35592#ebayphotohosting

Time to bid brother. 8)

[Guest]

If you don't win the bid...I have a gsxr 1100 and gs1100 swing you can have one for 50.00...

I've got a polished gs1100 swing with chrome axle and adjusters for 75.00

[Anonymous]

gs1100 swingarm

hey guys guess what??? that's the same swingarm i am bidding on!!!! Katman, did you say you had a gsxr twin shock arm for 50.00??? and it's longer? i will be drag racing mine alot this would be bennificial to me.would you sell that arm to me and ship it to Ashland,OH.of coarse i would pay all the shipping cost. this might work out great for everyone then.let me know soon please.and i won't bid on the gs 1100 arm.Thanks.

[Guest]

Hey Katman, I could be interested in that gs1100 swing arm that you have if sabian doesn't want it.

[Guest]

My gixxer arm isn't modified yet for twin shocks..no. You have to weld on some shock mounts, it is stock right now.

I have three gs1100 alum swingarms as well.

[Anonymous]

i can mod the swingarm myself,(for the twin shocks) or i might just mono my frame.So, was that a yes you would sell gsxr swingarm to me, or no you won't?what about one of the GS1100 arms??thanks

[Anonymous]

katman, thanks for the offer but right now i'm unable to buy anything for my bike or car, but thanx for the offer. my wife just had a baby last wensday. thanx again.

[Rico]

Wider and stretched????
Don't like the corners???

The world does need more drag bikes

learn how to tie down your forks buy a Nitros setup and go (I guess)

With all the goofing aside. Keep your eye on ebay. I ofton see stretched s/arms there. OR you can take your old s/arm to a fab shop and have it stretched. It's a perty straight foward job. And like others have said, with minor mods you can put a 180 on the.

have fun :roll:

Rico

[Anonymous]

thanks guys for all the info. this sight and everyone i've talked to has been nice and helpful. can't find too many websites like this. thanx again.

[Anonymous]

I've been thinking about getting a different swing arm also would the gs 1100 swing arm fit in a 78 gs 750 frame?

[Anonymous]

1150 arm

I took two GS1150 arms and made a 8" ich extended arm for my GS1100. I cut all the mono shock stuff off and welded shock mounts on it for the shocks. I run a 95 GSXR600 front end with A single disc up front and a 6 piston caliper from a Hayabusa. The rear uses a 5.5 inch wheel from a GSXR along with the brake and 530 Chain and sprocket. In front I run a 17 tooth Bnadit 1200 sprocket shimmed out to line up the chain. It's low and mean and draws a crowd always.