Announcement

Collapse
No announcement yet.

Still Won't Idle! I think I'm done.

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Originally posted by UncleMike View Post
    Okay, okay. One more thing to tackle.

    Although, I thought if you poured oil in and the psi's rose, that indicated that it wasn't valves.
    When you poured oil in the compression raised on even the non-low cyls. And it actually raised (I think) to abnormally high levels for the non-low cyls. That means the oil is either sealing "too well" or you put too much oil in (as somebody already mentioned), and you're getting basically bogus readings.

    Even if you are losing a bit of compression past the rings, you have no idea how much compression you're loosing due to too-tight valves. Get the valves in spec (which you can easily adjust), then you can do another compression check and find out the health of your rings (which you can't adjust).

    Your compression and your carb sync could both be significantly off with misadjusted valves. This could easily the the cause, or at least an aggravation of the cause, of all your trouble.

    Comment


      Originally posted by t3rmin View Post
      When you poured oil in the compression raised on even the non-low cyls. And it actually raised (I think) to abnormally high levels for the non-low cyls. That means the oil is either sealing "too well" or you put too much oil in (as somebody already mentioned), and you're getting basically bogus readings.

      Even if you are losing a bit of compression past the rings, you have no idea how much compression you're loosing due to too-tight valves. Get the valves in spec (which you can easily adjust), then you can do another compression check and find out the health of your rings (which you can't adjust).

      Your compression and your carb sync could both be significantly off with misadjusted valves. This could easily the the cause, or at least an aggravation of the cause, of all your trouble.
      I see. Time to learn something else!

      Thanks, everyone!

      Comment


        Originally posted by UncleMike View Post
        I see. Time to learn something else!

        Thanks, everyone!
        Dont ever give up,just get even!

        Comment


          Originally posted by tconroy View Post
          Dont ever give up,just get even!
          Endeavor to persevere.

          Comment


            Mike, I haven't been able to stick with your thread because I've been busy. I'll be busy today and this weekend too but you're getting help anyway. Just letting you know so you don't think I'm ignoring you.
            I too assumed the valves were adjusted, along with a few other things.
            You guys know I always say to check all the basic maintanance things first, then troubleshoot. Basics are good compression/not burning oil, valve clearances set, good fuel flow/clean-rebuilt carbs/tank/petcock, clean air filter, good spark/timing/clean electrical connectors and good plug leads, etc.
            Part of the problem as pointed out earlier is that this is a long thread and I believe this thread isn't the first one about this bikes problems. So people kind of forget what's been done to fix a problem.
            Your compression reads, while not balanced, are still within spec but ideally the difference shouldn't be more than 10% unless the factory manual says different. I don't believe those reads would indicate/cause your problem though. Maybe a little uneven idle but not "intake leak" symptoms.
            I've taken apart a few bikes that had their valve clearances all over the place with some at less than .02mm clearance and some more than .20 mm. They weren't running well but none of them had rpm's rising significantly with engine temp. But you should adjust those valves because it's part of the basic tuning. Adjust on a stone cold engine only, overnight is best.
            I'd re-check the compression with a completely warmed up engine (same temp as when the rpm's rise up) and see what the reads are then.
            And on the seventh day,after resting from all that he had done,God went for a ride on his GS!
            Upon seeing that it was good, he went out again on his ZX14! But just a little bit faster!

            Comment


              Originally posted by KEITH KRAUSE View Post
              Mike, I haven't been able to stick with your thread because I've been busy. I'll be busy today and this weekend too but you're getting help anyway. Just letting you know so you don't think I'm ignoring you.
              I too assumed the valves were adjusted, along with a few other things.
              You guys know I always say to check all the basic maintanance things first, then troubleshoot. Basics are good compression/not burning oil, valve clearances set, good fuel flow/clean-rebuilt carbs/tank/petcock, clean air filter, good spark/timing/clean electrical connectors and good plug leads, etc.
              Part of the problem as pointed out earlier is that this is a long thread and I believe this thread isn't the first one about this bikes problems. So people kind of forget what's been done to fix a problem.
              Your compression reads, while not balanced, are still within spec but ideally the difference shouldn't be more than 10% unless the factory manual says different. I don't believe those reads would indicate/cause your problem though. Maybe a little uneven idle but not "intake leak" symptoms.
              I've taken apart a few bikes that had their valve clearances all over the place with some at less than .02mm clearance and some more than .20 mm. They weren't running well but none of them had rpm's rising significantly with engine temp. But you should adjust those valves because it's part of the basic tuning. Adjust on a stone cold engine only, overnight is best.
              I'd re-check the compression with a completely warmed up engine (same temp as when the rpm's rise up) and see what the reads are then.
              Thank you, Keith. Valves are next on my list, and then I'll figure out where the hell I've got an intake leak coming from.

              Mike

              Comment


                Originally posted by UncleMike View Post
                Thank you, Keith. Valves are next on my list, and then I'll figure out where the hell I've got an intake leak coming from.

                Mike
                Since we're going back over the basics:

                1) Have you ever actually done a vacuum carb sync?

                2) Have you checked that the screws plugging the vacuum ports on the intake runners are in there tight?

                Comment


                  Originally posted by t3rmin View Post
                  Since we're going back over the basics:

                  1) Have you ever actually done a vacuum carb sync?

                  2) Have you checked that the screws plugging the vacuum ports on the intake runners are in there tight?
                  Yes and yes.

                  Comment


                    So, anyone want to help me with 16v valve adjustment?

                    I've got the cover off and the crankshaft turned so that the T is showing through the window. The notches on the cams are pointing in at one another, if I'm looking at the right thing.

                    What I'm not sure of is what the hell Table 8 is supposed to be telling me, and where I'm supposed to be sliding the feeler gauge.

                    Comment


                      Originally posted by UncleMike View Post
                      So, anyone want to help me with 16v valve adjustment?

                      I've got the cover off and the crankshaft turned so that the T is showing through the window. The notches on the cams are pointing in at one another, if I'm looking at the right thing.

                      What I'm not sure of is what the hell Table 8 is supposed to be telling me, and where I'm supposed to be sliding the feeler gauge.
                      Table 8 is telling you which valves you can adjust with the cam markings in the given position. So if your cam markings are point in, you can adjust the #4 valves (and some others).

                      You want to insert the feelers between the cam lobe and the follower bearing surface.

                      Adjustment is very easy.

                      1. Loosen both jamb nuts and back out the screws until you can get the .10 mm feeler in there smoothly.

                      2. Tighten the screws until you find the point where any further tightening on either screw will cause the feeler to hang up. This takes some practice.

                      3. Without moving the screws, use a 10 mm socket to tighten the jamp nuts. They sell a special tool for this job but you can manage with a regular socket and a pair of needle nose pliers, IMO.

                      4. Turn the crank a few times and go back to the same cam position.

                      5. Check the clearance again. I like to have it where the .10mm fits evenly but the .11 doesn't. The range in the manual is .09 to .13

                      Comment


                        Thanks!

                        It's where the feeler gauge should be sliding in that's hanging me up.

                        For instance:

                        You want to insert the feelers between the cam lobe and the follower bearing surface.

                        I don't know what a lot of those words mean. I'm assuming "cam lobe" is the part of the camshaft that depresses the valves as it spins, and is shaped like an egg from the side?
                        Last edited by Guest; 11-03-2006, 02:33 PM.

                        Comment


                          Yes, that's the lobe, the follower often looks like the head of a hammer (not sure on these bikes) but it's basically the bit the lobe contacts with and moves up & down as CAM goes round. You want to adjust the clearance at the base of the "egg" usually....

                          Dan
                          1980 GS1000G - Sold
                          1978 GS1000E - Finished!
                          1980 GS550E - Fixed & given to a friend
                          1983 GS750ES Special - Sold
                          2009 KLR 650 - Sold - gone to TX!
                          1982 GS1100G - Rebuilt and finished. - Sold
                          2009 TE610 - Dual Sporting around dreaming of Dakar..... - FOR SALE!

                          www.parasiticsanalytics.com

                          TWINPOT BRAKE UPGRADE LINKY: http://www.thegsresources.com/_forum...e-on-78-Skunk/

                          Comment


                            Originally posted by salty_monk View Post
                            Yes, that's the lobe, the follower often looks like the head of a hammer (not sure on these bikes) but it's basically the bit the lobe contacts with and moves up & down as CAM goes round. You want to adjust the clearance at the base of the "egg" usually....

                            Dan
                            Hmmm,...I would think it would be in constant contact with the follower then, and you wouldn't be able to get any of the feelers in there, and I can't.

                            Not to mention the fact that it wouldn't seem to make sense that there would be individual adjustments for each valve then, would it? I'm thinking that if the lobe is acutating two valves at a time, why not just have one adjuster for both valves?

                            Comment


                              Originally posted by UncleMike View Post
                              Hmmm,...I would think it would be in constant contact with the follower then, and you wouldn't be able to get any of the feelers in there, and I can't.

                              Not to mention the fact that it wouldn't seem to make sense that there would be individual adjustments for each valve then, would it? I'm thinking that if the lobe is acutating two valves at a time, why not just have one adjuster for both valves?
                              I am really not familiar with the 16v bikes or the adjustment thereof, but, you need an adjustment for each valve because they won't necessarily wear evenly. Valve adjustment is there to correct for wear, which causes clearances to go one way or another (depending on what's wearing and how much, in relation to other stuff wearing...).

                              As to where to stick the feeler, you stick it between the cam lobes and the thing below the lobes which they contact and push down (*edit* actually between the thing that ultimately pushes the valve tappets down and the valve tappets). The idea is there should be a certain amount of clearance between the lobe and the thing it pushes on (actually between the thing the lobe pushes on, and the things it pushes on) when it's NOT being pushed (it only pushes when the longer side of the lobe is downward). If there's not enough clearance, the valve may not close all the way and if there's too much it may not open enough or stay open long enough.

                              *sigh* I tried to make that simple, but it doesn't sound simple. ;-)
                              Last edited by Guest; 11-03-2006, 03:07 PM. Reason: 16v

                              Comment


                                Originally posted by UncleMike View Post
                                Hmmm,...I would think it would be in constant contact with the follower then, and you wouldn't be able to get any of the feelers in there, and I can't.

                                Not to mention the fact that it wouldn't seem to make sense that there would be individual adjustments for each valve then, would it? I'm thinking that if the lobe is acutating two valves at a time, why not just have one adjuster for both valves?
                                The lobe shouldn't be operating two valves at a time(on a 8 valve engine). As far as the cam follower adjustment, I'll have to consult my book.
                                On edit, one cam lobe could probably operate two valves simultaneously on a 16 valve, but the measurements would have to be equal.
                                Last edited by Guest; 11-03-2006, 03:00 PM. Reason: Didn't realize it was a 16 vlv

                                Comment

                                Working...
                                X