1981 GSX1100 Katana Based Project

[Shin-Ken 1074]

My factory mirrors.

Mirror factory by Max Mutarn, on Flickr

[Shin-Ken 1074]

While I am waiting for the mirrors to arrive and see what they weigh, hopefully less than OEM mirrors, I had time to fit the volt meter today. Made the bracket last week and left it over the weekend
for the paint to cure. Adding weight is the opposite to what this build is about however, my electrical adviser strongly suggested that a volt meter is a must have to monitor a lithium battery. In our riding group several lithium batteries have failed with three of them popping the cases and luckily not catching fire. The cause was over-charging and the bikes did not have volt meters fitted so the owners had no way of knowing there was a problem until there was a problem. Found a light weight volt meter that fits under the engine temp gauge and doesn't look too over the top on a vintage Kat. The running tally is jumping up a few grams today.

volt meter 4 by Max Mutarn, on Flickr


volt meter bracket 3 by Max Mutarn, on Flickr


volt meter 5 by Max Mutarn, on Flickr

Running tally = 199.800 kg.

[Shin-Ken 1074]

The mirrors arrived today, 773 grams total for the pair. I was hoping they would be lighter having aluminium stems so this will take a bit of work to make them lighter. If I can get them down to 600 grams that will be just over 30% lighter than the OEM mirrors so that means taking 87 grams off each mirror. Not keen on drilling holes in the stem so it will be changing the profile of the stems to lighten them.

Mirrors before mods.
Mirrors 1 by Max Mutarn, on Flickr

[Shin-Ken 1074]

Update on the mirrors, the stems are cast aluminium and not forged aluminium so drilling or thinning down the stems may weaken them. For now the mirrors will stay as supplied and not be modified however, because they are wider than "Old School" Suzi Kat mirrors I can now see in the mirrors without "Katana Elbow" so that's an improvement and the new mirrors look sporty so two wins.

To align the right mirror with the left mirror I had to make a bracket to position the mirror forward of the mirror mount on the bar.
Mirror 5 by Max Mutarn, on Flickr


Mirror 6jpg by Max Mutarn, on Flickr

[Shin-Ken 1074]

The muffler that had been used for the build decided it didn't want to be on the Team and threw in the towel, the titanium inlet parted company with the can flange. I found a pretty decent used carbon and stainless muffler to replace the damaged titanium unit and installed it today. Sounds good and looks good so all is good!


muffler b1 by Max Mutarn, on Flickr


Muffler b2 by Max Mutarn, on Flickr


Muffler b3 by Max Mutarn, on Flickr

[Shin-Ken 1074]

I scored some used carbon parts on the weekend so a few more grams to be shed once they are installed. Also having a set of machined aluminium mirror mounts made to replace the current set that just look wrong as well as being heavier than they need to be. Pics of carbon parts and mirror mounts will be posted here when they arrive.

[Shin-Ken 1074]

The project Kat had a full length carbon chain guard fitted and although lightweight when compared to the OEM steel chain guard, there are lighter aftermarket guards out there in the wild. Caught this tidy used carbon guard, sooo light.

Carbon guard MKII by Max Mutarn, on Flickr


Carbon guard MKII b by Max Mutarn, on Flickr


Running Tally = 199.694 kg.

[Shin-Ken 1074]

Also found a used aftermarket carbon instrument cover that will be installed sometime down the line.

Carbon instrument cover b by Max Mutarn, on Flickr

[Shin-Ken 1074]

The super light weight chain guard was supplied with a titanium allen bolt and aluminium spacer. The spacer is needed to off-set the guard position as the 520 rear sprocket is installed 8mm closer to the wheel than the stock carrier due to using a lighter sprocket carrier.

Carbon guard hardware a by Max Mutarn, on Flickr

[Shin-Ken 1074]

As I have mentioned before in this build the low hanging fruit has been picked bare so from now on it will be fine tuning of parts to reduce weight, a few grams here and a few grams there. Today I revisited the mirror mounts and swapped them for thinner wall aluminium mounts, every gram taken off is a win.


Mirror mount a by Max Mutarn, on Flickr


Mirror mount b by Max Mutarn, on Flickr


Mirror mount c by Max Mutarn, on Flickr

Running Tally = 199.677 kg.

[Diirk]

Haven't been on the forum for over half a year and it was quite a treat to read up on the project as well as seeing it's still going in 2025.
Happy new year's, mate! and best of luck keeping the tally below 200kg.

[Shin-Ken 1074]

Haven't been on the forum for over half a year and it was quite a treat to read up on the project as well as seeing it's still going in 2025.
Happy new year's, mate! and best of luck keeping the tally below 200kg.

Hi Diirk, thanks mate and a Happy New Year to you. Yes, the build continues to get lighter, the next goal is to hit 199.00 kg. Finding 677 grams would be easy if I swapped the OEM indicators for LED units but then it wouldn't look right and if it doesn't look right it isn't right. Swapping mirrors could be an option?

Cheers mate.

[Shin-Ken 1074]

Replaced a few more bolts today with lighter ones. The bolts are not critical so no need for steel bolts, aluminium and Ti will do the job just fine.

steel bolts ac by Max Mutarn, on Flickr


IMG_882Ti bolts ac by Max Mutarn, on Flickr


Titanium bolts ab by Max Mutarn, on Flickr


Aluminium bolts ab by Max Mutarn, on Flickr


Running tally = 199.632 kg.

[Shin-Ken 1074]

The M6 aluminium bolts replaced the Ti bolts that held the seat support brackets.

Seat brackets by Max Mutarn, on Flickr

[Shin-Ken 1074]

These M5, M6 and M8 aluminium bolts arrived today, they are to replace the titanium bolts currently holding the cowl brackets in place and a few other brackets that don't need Ti or steel to secure them. Much lighter than titanium or steel bolts so once installed the running tally will be adjusted.

Ally bolts 1 by Max Mutarn, on Flickr