Project GS1000 with GS1100G D-Port Head, 1100G Cylinder & Mikuni RS34

Wow, amazing build out. Too bad you have a long wait until next ride huh?

Quick question, when dropping on the cylinder, how do you get all the rings compressed at the same time while also lowering the head? I've done it on single cylinders before but never 4!

Thanks,
Sci85

[srsupertrap]

GS1000S fairing reinstalled & ready for next season

[srsupertrap]

Re-reading the thread, you mention S-1 AND S-3 cams.
Which ones are you running in it or did you use one of each and in which positions?
I have the S-3 cams (both) in my true 1100cc (73.5mm bore, 1000 motor) in my '79 750E with 29mm Smooth-bores and it runs like a scalded dog.
Especially above 6,000 rpm.
I milled the head .020 to bump the compression up a little more.
It is still my favorite weapon of choice and I have a few to choose from.
Once that baby is fully broken in, it will be your favorite as well I am certain.


Daniel

Daniel,

I looked back and I was referring to the Cylinder Head Casting Id Number which is located adjacent to the cylinder head surface. The original GS1000 head was marked with a S-1 through S-3 number. The GS1100G, at least mine was identified with a S-6 Mark

Back to the cams I only have the Andrews S1 cams installed in both Intake & exhaust positions. I have always liked street cams because it lets you roll by unsuspecting maladjusted 600 Sewing Machines w/o sacrificing reliability


Here is a photo of GS1100G Head: S-6 Marked Lower Rt. If anyone knows all design changes between the original GS1000 S-1 head & GS1100G head that would be interesting to know. I only know the D-port, bigger chamber etc

PS: I also have a GS1100G Head 4 Sale

I think I hear angels.

Re-reading the thread, you mention S-1 AND S-3 cams.
Which ones are you running in it or did you use one of each and in which positions?
I have the S-3 cams (both) in my true 1100cc (73.5mm bore, 1000 motor) in my '79 750E with 29mm Smooth-bores and it runs like a scalded dog.
Especially above 6,000 rpm.
I milled the head .020 to bump the compression up a little more.
It is still my favorite weapon of choice and I have a few to choose from.
Once that baby is fully broken in, it will be your favorite as well I am certain.


Daniel

[srsupertrap]

I really appreciate all the positive comments from psyguy, 80GS1000, Flyboy, sedelen, 7981GS & of course jeff.saunders in the last couple of threads from my fellow GSer brothers , I hope this thread sticks around and helps someone in the future with their GS1000/1100 2V project. BTW this thing now displaces 1100cc with Wiseco 73.5mm


A couple of points:

1. If you do this modifcation your pistons should be at least 73.5mm since the stock GS1100G displaces 1074cc. Asking a Machinist to bore out the 1074 sleeves to accept the familiar Wiseco 1085 (73mm pistons) is splitting hairs IMO.
2. How does it run? Its really stout with a noticeable seat of the pants Ooomph factor. I got super lucky with the RS34 Jetting, I installed Mains: 120 & Pilot 15s and it started up just fine not cough, stutter, backfiring etc
3. The bike feels a bit heavier which I attribute to the heavier 1100G cylinders; the previous 1085cc cylinders were razor thin
4. I will post a picture with the GS1000S fairing soon

PS: I will retorque the Head soon

so is that colour silver rather than white?

yeah... what everyone else said... superb perfection excellent georgeous... and to repeat myself... sexy

One of the most informative, enjoyable threads I have read, many thanks for sharing.
That bike is gorgeous.

Excellent work! Bravo...

Think of all the money you'll save from the front wheel being off the ground all the time with those new RS34s...power wheelie city my brother.

I swear I have witnessed perfection in this rebuild thread.
What a bike!

I love that paint scheme! WTG!!!
So now the bike is a 1055? Sweet!

Daniel

Superb job on the bike.

Don't forget to retorque the cylinder head.

[srsupertrap]

+1: psyguy on Mikuni Carbs. I must have completed lot of work back on 7/30/2011 based on all the pictures I took




I turn the engine over & over by hand to ensure all the oil passages are filled, I even see the oil level drop a couple of times.

I wheel the big GS next to my Tacoma: Attach some jumper cables to its battery, twist the grip twice & pull the choke fully put, hit the starter button and it starts immediately. Being everything is new I blip the throttle up to 3.5K immediately.


Besides the Idle Speed being too high the new Carbs settle down into their Clickty clack idle as I continue to blip the throttle. I turn it off after a minute since smoke is coming from the newly painted header, Cylinder & Head etc. I turn on the fan and repeat the process increasing the run time by a couple of minutes each time



Parked after first break in run. Nothing leaks at all and the bark from the Supertrapp is more pronounced. Lessons learned soon to follow. . . A real Master Charger

those carbs are very sexy

That looks like some serious flow from those fuel lines.
And easy to see.

Daniel