Barcket racing season starts Jan 4th

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • blowerbike
    Forum Guru
    GSResource Superstar
    • Aug 2008
    • 7057
    • Ohio Closer to KY Than Cleveland

    #16
    you strapped the front....

    Comment

    • Guest

      #17
      Originally posted by blowerbike
      you strapped the front....
      yes I do but that's not it
      I went early to test with the slider clutch and set it up I ended up getting a 10.62 @124 and I think I can get it a little lower with some more testing. I didn't want to mess with it once we started the program.
      Last edited by Guest; 01-19-2014, 09:55 PM.

      Comment

      • blowerbike
        Forum Guru
        GSResource Superstar
        • Aug 2008
        • 7057
        • Ohio Closer to KY Than Cleveland

        #18
        ha!
        i see the oil fill cap on the side now...
        leaving from an idle or on a 2 step?

        Comment

        • Guest

          #19
          Originally posted by blowerbike
          ha!
          i see the oil fill cap on the side now...
          leaving from an idle or on a 2 step?
          I leave from a high idle. The slider is set at about 3200 rpm

          Comment

          • trippivot
            Forum Sage
            Past Site Supporter
            • Aug 2006
            • 2815
            • Des Moines , IA

            #20
            18 package - great job , that is hard to get under.. Your opponent broke out trying even though you had it from the start.

            3200 stall wow do you use MTC springs or do you have a different combo?
            SUZUKI , There is no substitute

            Comment

            • Guest

              #21
              Originally posted by trippivot
              18 package - great job , that is hard to get under.. Your opponent broke out trying even though you had it from the start.

              3200 stall wow do you use MTC springs or do you have a different combo?
              I set it up using the stock inner valve springs from a Kawi KZ1000 and use 2 washers on the arms.
              I can get it to come in as low as 2200 rpm. I used a slider in my stock wheel base 1150 years ago with this set up. I just put that slider in until I can get my pro et bike finished here is a pic of it so far
              Last edited by Guest; 01-20-2014, 05:19 PM.

              Comment

              • Guest

                #22
                I just scored on what I feel is a great deal on some carbs on E-Bay my max bid was more than I paid. For my pro-et bike check them out. let me know good deal or not. I guess I am happy camper. I think the only thing I need now is tires. The slicks are almost new but 8 years old. I am not to trusting of old tires.

                http://www.ebay.com/itm/181306481065...84.m1497.l2649
                Last edited by Guest; 01-29-2014, 03:54 PM.

                Comment

                • tom

                  #23
                  Originally posted by stetracer
                  I just scored on what I feel is a great deal on some carbs on E-Bay my max bid was more than I paid. For my pro-et bike check them out. let me know good deal or not. I guess I am happy camper. I think the only thing I need now is tires. The slicks are almost new but 8 years old. I am not to trusting of old tires.

                  http://www.ebay.com/itm/181306481065...84.m1497.l2649
                  dont run that tire please the ruber dries out with age and might not show cracks by eye 8 year old tire going 140 mph or faster is nuts .

                  Comment

                  Working...