Announcement

Collapse
No announcement yet.

Time for upgrading fork springs?

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Time for upgrading fork springs?

    Im noticing that when we ride two up my hands go numb more often than when I ride solo. Could this be a sagging front end, thereby putting more of my weight on my hands? As far as I know the only work done on these forks has been replacing the seals.

    Input please, and thank you

    Roger
    Roger

    Current rides
    1983 GS 850G
    2003 FJR 1300A
    Gone but not forgotten 1985 Rebel 250, 1991 XT225, 2004 KLR650, 1981 GS850G, 1982 GS1100GL, 2002 DL1000, 2005 KLR650, 2003 KLX400

    #2
    Lot's of good reasons to replace fork springs, but this isn't one of them. Passenger weight doesn't really load the forks at all, all that weight is directly over the rear axle.
    '20 Ducati Multistrada 1260S, '93 Ducati 750SS, '01 SV650S, '07 DL650, '01 DR-Z400S, '80 GS1000S, '85 RZ350

    Comment


      #3
      My guess is that riding two up is changing your posture. Not necessarily the front forks. Or your lady could be holding on so hard that she is cutting off circulation to your arms

      Comment


        #4
        The 850 forks use soft springs and air pressure to fine tune the ride. Some guys don't know this so they ride around without any air in the forks, in which case the front end will sag and bottom out often, not to mention the compressed forks will throw the riders weight forward. I'm not sure if this is applicable to the problem but if you are not adding air you may want to check out the owners manual and pump some air in the forks to see if this improves the front end feel and comfort in general. Adding air is a pain in the butt because it will leak out in time. That's why lots of guys swap out the soft OEM springs for something stiffer which makes using air unnecessary.
        Ed

        To measure is to know.

        Mikuni O-ring Kits For Sale...https://www.thegsresources.com/_foru...ts#post1703182

        Top Newbie Mistakes thread...http://www.thegsresources.com/_forum...d.php?t=171846

        Carb rebuild tutorial...https://gsarchive.bwringer.com/mtsac...d_Tutorial.pdf

        KZ750E Rebuild Thread...http://www.thegsresources.com/_forum...0-Resurrection

        Comment


          #5
          Thanks guys. I don't feel the front bottoming out but will check the pressure tomorrow. I'm always telling my kids to read the manual, so I need to heed my own advice.. haha. Owners manual says 11psi.

          It is likely my posture does change. She doesn't really usually even touch me so it's not that she's holding too tight, usually!

          I'm not in a hurry to tear into the forks and replace the springs yet so hopefully the air helps.

          Thanks again
          Roger

          Current rides
          1983 GS 850G
          2003 FJR 1300A
          Gone but not forgotten 1985 Rebel 250, 1991 XT225, 2004 KLR650, 1981 GS850G, 1982 GS1100GL, 2002 DL1000, 2005 KLR650, 2003 KLX400

          Comment


            #6
            Interesting that you only notice the difference while carrying a passenger.

            Question: have you changed the fork oil recently? If so, what viscosity did you put back in?

            My experience: When I got my Wing (11 years ago), the previous owner had changed the forks to Progressive Suspension and had installed the recommended 15w oil. I found that on an all-day ride, my wrists were hurting. Certainly not because of any weight applied, as I sit quite upright. I noticed that my arms were being jerked on any small bump because of a lack of compliance in the suspension. I drained the oil and refilled with 10w, I have since done several 700+ mile days with no pain in the wrists.

            Check for posture differences when she is on, and also check (change) your fork oil.

            .
            sigpic
            mine: 2000 Honda GoldWing GL1500SE and 1980 GS850G'K' "Junior"
            hers: 1982 GS850GL - "Angel" and 1969 Suzuki T250 Scrambler
            #1 son: 1986 Yamaha Venture Royale 1300 and 1982 GS650GL "Rat Bagger"
            #2 son: 1980 GS1000G
            Family Portrait
            Siblings and Spouses
            Mom's first ride
            Want a copy of my valve adjust spreadsheet for your 2-valve per cylinder engine? Send me an e-mail request (not a PM)
            (Click on my username in the upper-left corner for e-mail info.)

            Comment


              #7
              No, I haven't checked or changed the fork oil since I bought the bike in July of last year. I will now though.
              Roger

              Current rides
              1983 GS 850G
              2003 FJR 1300A
              Gone but not forgotten 1985 Rebel 250, 1991 XT225, 2004 KLR650, 1981 GS850G, 1982 GS1100GL, 2002 DL1000, 2005 KLR650, 2003 KLX400

              Comment


                #8
                One more thought: even if you have the proper viscosity oil, if the level is too low, you will have some interesting results. I experienced that on my Kawasaki Voyager many years ago. It rode VERY nicely on smooth roads, but with the slightest hint of uneven roads, it acted like solid suspension. I found the fork oil level low. Basically, the damper was floating in air at normal ride height, but when the ride height changed due to a dip or a bump, the damper basically did a belly flop into the oil. The transition from air to oil was rather harsh, giving the feeling of solid suspension. Simply adding the correct amount of oil restored a nice, cushy ride.

                .
                sigpic
                mine: 2000 Honda GoldWing GL1500SE and 1980 GS850G'K' "Junior"
                hers: 1982 GS850GL - "Angel" and 1969 Suzuki T250 Scrambler
                #1 son: 1986 Yamaha Venture Royale 1300 and 1982 GS650GL "Rat Bagger"
                #2 son: 1980 GS1000G
                Family Portrait
                Siblings and Spouses
                Mom's first ride
                Want a copy of my valve adjust spreadsheet for your 2-valve per cylinder engine? Send me an e-mail request (not a PM)
                (Click on my username in the upper-left corner for e-mail info.)

                Comment

                Working...
                X