Announcement

Collapse
No announcement yet.

Gs 550 callipers

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Gs 550 callipers

    Hi Guys.
    I am rebuilding a gs 550. Registered in 1980 but a check on the vin numbers says the frame is 1978 gs550d and the engine is 1979 gs550e and it has cast wheels, so am not worried about everything matching. But what I want to know is do the front and rear callipers fit any model, are they interchangeable?
    If not my front ones are damn huge, with an internal 'floating' arm which mounts to the forks for want of a better description. They have a rubber bellows where the arm goes into the body. Dies anyone know where I can get these bellows from?

    #2
    I'm not trying to sound snarky but hope you realize that Suzuki sells parts. I'm not sure what the best source is in the UK but some members here mention this place...https://www.robinsonsfoundry.co.uk/s...brake-calipers

    To learn what parts fit what models you can try cross-referencing the part numbers. If you use a site like Partzilla.com it will show you this information straight away too.
    Ed

    To measure is to know.

    Mikuni O-ring Kits For Sale...https://www.thegsresources.com/_foru...ts#post1703182

    Top Newbie Mistakes thread...http://www.thegsresources.com/_forum...d.php?t=171846

    Carb rebuild tutorial...https://gsarchive.bwringer.com/mtsac...d_Tutorial.pdf

    KZ750E Rebuild Thread...http://www.thegsresources.com/_forum...0-Resurrection

    Comment


      #3
      Robinsons are as good as any - I've used them a lot over the years.

      Two different types of front caliper were fitted to UK 550s, depending on model year. Basically the earlier ones had round pads, while the later ones had pads that were virtually rectangular. If in doubt, post a photo.
      1980 GS550ET

      Comment


        #4
        Thanx for the replies. Cross referencing part numbers will get the same callipers but this is not what I want. I have the round pad brakes and want to change them coz they are monstrous. What I need to know is if the other callipers have the same hole pitch for the mounting blocks and whether they will sit on the disc in the correct attitude.

        Comment


          #5
          Why not cross reference the lower fork tubes? That will show if the early and later calipers share the same fork parts, thus indicating compatibility. Pretty sure they interchange but I don't want to be responsible if they aren't. I do know that folks here have put later calipers on some of the (early) bigger bikes but I've never studied the situation for the 550.
          Ed

          To measure is to know.

          Mikuni O-ring Kits For Sale...https://www.thegsresources.com/_foru...ts#post1703182

          Top Newbie Mistakes thread...http://www.thegsresources.com/_forum...d.php?t=171846

          Carb rebuild tutorial...https://gsarchive.bwringer.com/mtsac...d_Tutorial.pdf

          KZ750E Rebuild Thread...http://www.thegsresources.com/_forum...0-Resurrection

          Comment


            #6
            I'm also fairly sure, but not 100%, that they will interchange. But the later calipers are no smaller. I don't have two to hand to compare, but from memory, the later ones may be a little larger.

            If you're determined to have small calipers, you'll be looking at changing discs, making spacers,adjusting hoses, maybe changing fork legs etc. Check out some of saltymonk's threads to see how some people have upgraded their brakes.
            1980 GS550ET

            Comment


              #7
              The later square pad type (there are actually 2 very similar but different square types) are a little larger than the round pad type. All 3 twin disc set ups are plug and play (though avoid the leading axle calipers from the L and some GSX bikes - they don't fit). The later type offer quite an improvement on braking. Fitted to the 550, 650, 750, 850 and 1000.
              79 GS1000S
              79 GS1000S (another one)
              80 GSX750
              80 GS550
              80 CB650 cafe racer
              75 PC50 - the one with OHV and pedals...
              75 TS100 - being ridden (suicidally) by my father

              Comment


                #8
                If you're looking for a set I have a set of the most modern of the GS ones from an 82 1100G (complete with master cylinder, still sealed). They were rebuilt (prob more than a year ago) and have new pads & NOS rubber lines. Probably done 1,000 miles or so since rebuild.

                I believe you could potentially also do the Twinpot mod on that bike if it has the 2 brake disks. You can see details in my sig. I have a few sets of brackets & spacers on my shelf.

                I will be in London over Christmas so could potentially bring parts back with me (Although I think I'd have to empty the brake system of fluid to check it on a flight - I have a friend who works at the airlines that can confirm that)
                1980 GS1000G - Sold
                1978 GS1000E - Finished!
                1980 GS550E - Fixed & given to a friend
                1983 GS750ES Special - Sold
                2009 KLR 650 - Sold - gone to TX!
                1982 GS1100G - Rebuilt and finished. - Sold
                2009 TE610 - Dual Sporting around dreaming of Dakar.....

                www.parasiticsanalytics.com

                TWINPOT BRAKE UPGRADE LINKY: http://www.thegsresources.com/_forum...e-on-78-Skunk/

                Comment


                  #9
                  Thanx for the replies, great info there. I do wish you hadn't mentioned the twin pot conversion though, my mind and my eBay finger are twitching like mad. 😀😀

                  Comment

                  Working...
                  X