• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

Do I have a DynoJet kit installed?

  • Thread starter Thread starter mark_vaughn
  • Start date Start date
M

mark_vaughn

Guest
Basically wanting to figure out if I already have the parts installed.

The bike had some mods already when I got it and I am told it ran well when it was parked, I never saw it.

Has a 4-1 already, so it may have more mods... Want to make sure before I drop a few hundred on a dynojet kit.
 
two ways to check, see if the needles that are installed have grooves to raise e and lower the needle. Take of the 4 screws on top of one of the carbs and you should be able to answer the question in 5 minutes with it back together in 10.

The other way is to pull a float bowel and look at the size of the main jet.
 
the main jet will also have the letters D and J on it before the size
 
So I have 125 jets installed.

I will be running pods and a stock exhaust.

Any thoughts on if these jets will work? Don't want to be too lean.
 
You can find the complete parts lists at the dynojet site. The 3133 is the one you would get.

Pods make the biggest difference interms of flow. The combination of 4:1 and pods will probably want you around 132 DJ mains.

http://www.dynojet.com/pdf/3133.pdf


The next thing to figure if you have Dyno jet mains or Mikuni mains. They are roughly related as below:

DJ = Mikuni+10

So if you have Mikuni 125's now then you are set for Pods and 4:1 already. If not then you will likely need to step it up. But sound like someone was already going some jetting problem now if to know what needles you have. Are the DJ?
 
That's a good size main for those mods but what are the spark plugs telling you?
Get the Dynojet kit for the needle and drill the slide or you won't be happy with the pods.
 
I dont see any markings on the needle.

Any clearer explanation on how to tell the size of the needle?
 
Is the needle tapered with notches where the clip and spacers go?
If not bite the bullet
 
Mikuni jets

picture.php


Dynojet needles (the ones with the grooves)

picture.php
 
You must log in or register to reply here.
Back
Top