• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

Help me Please!

  • Thread starter Thread starter brs127s
  • Start date Start date
B

brs127s

Guest
Hey folks,

Boy, I've really gotten myself into trouble this time. I was removing the wrist pins from the pistons from my 850 tonight, so I could measure the pistons and rings. As I was removing one of the wrist pin clips, I accidently dropped it. Problem is, I am not sure where it went. I have searched the floor and the tray under the bike. I have also looked in the bike. I can see the crank really well, and do not see it.

I plan on cleaning my basement floor up and looking one more time. My real question is, other than splitting the cases, is there any other way to search in the engine? I was going to pick up a retrieval magnet at the auto store tomorrow and try it in the area under the crank. What about removing the oil pan? Will it gain me any better access to the area under the crankshaft. Any help would be greatly appreciated.

Brandon
 
Removing the oil pan my help you.

You probably realize it NOW, but any time that you have the cylinders off, you should stuff some CLEAN shop cloths around the opening(s) into the cases, to prevent anything from falling inside.

Good luck!
 
Yep, I should have stuffed rags in the openings.

Actually, I am not convinced that it fell in the engine. I hadn't removed any of the pistons yet. Pistons 2 and 3 were down, 1 and 4 were up. I was removing the inside wrist pin clip from the no. 1 piston. At this point there wasn't much open area into the block exposed, unless it fell back under the no. 1 piston. If so, I should be able to see it. I can see the bottom of the engine under the no. 1 piston.

I will look again tonight. If it fell on the floor, it could have bounced a mile away. I will check the bike thoroughly again tonight. I am going to try a magnet and will probably pull the oil pan.
 
Get one of those tools that they sell for adjusting automobile carbs. They have a screwdriver handle and a flexible spring shaft that bends. They also have a magnetic end to hold the different bits. You may be able to fish it out with that if it fell into the crankcase.
 
Thanks Billy, I will pick on up tonight. I didn't realize those had flexible shafts. That would be even better than the regular magnetic retreiver.
 
I don't know if it would help or not,but I made 2 tools years ago that have helped me in similar situations. I mounted (with silicone) a 1'' round mirror
to the end of a 2' piece of #14 soft copper wire. With the help of a flashlight shined at an angle into the mirror,it has helped me to find things I could'nt see otherwise. It 's bendable and will get in anywhere the mirror will fit. If you can see it,then you can pick it up with a magnet mounted on another wire,as long as you have help. KK.
 
The wayward clip has been found. While I was working in the basement tonight, I thought I would use the flexible magnet I had bought and go fishing in the crankcase. Well, sure enough, the second try under rod No. 2, the clip came out on the magnet. My problem has been solved.

Billy, I did go and get a carb adjusting tool, but it did not have a strong enough attraction force. I then went to Sears, and bought a Craftsman flexible magnetic retrieval tool. It is pretty nice. The magnet is shielded until you push the plunger and make it go out of the shield.
 
You must log in or register to reply here.
Back
Top