• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

Turn siganals.?.? No flash

  • Thread starter Thread starter Jason Adam
  • Start date Start date
J

Jason Adam

Guest
So I wnated to swap out my rear signals. I grabbed some regular 12V lights(from TSC actually), but when I wire them up, I get the front and rear signal for whatever direction I select kicks on, but just stays lit, and so does the dash indicator.No flash. What gives? I put the originals back and they flash fine..
 
Jason Adam said:
So I wnated to swap out my rear signals. I grabbed some regular 12V lights(from TSC actually), but when I wire them up, I get the front and rear signal for whatever direction I select kicks on, but just stays lit, and so does the dash indicator.No flash. What gives? I put the originals back and they flash fine..
Click to expand...

Wrong wattage?

Did you make sure the grounds were hooked up properly?
 
I had the same problem. The origional turn signal lights use a lot of power, and this high current is required to make your stock flasher unit work.

Solution: $3 on a generic, two blade flasher unit at the local auto parts store. No rewiring required, just plug it in.
 
jm_foote said:
I had the same problem. The origional turn signal lights use a lot of power, and this high current is required to make your stock flasher unit work.

Solution: $3 on a generic, two blade flasher unit at the local auto parts store. No rewiring required, just plug it in.
Click to expand...

Could you elaborate on that. Am I replacing the current flasher with a two blade electric? I'm not much of a gear head, but very DC electrical knowlegable. Any info would be great. Thanks.
 
Flashers are fairly universal. So long as it plugs into the wiring harness, you are good.

Flashers use the current passing through them to break the circuit temporarily. Too much current (too many lights) and the flasher flashes too rapidly or doesn't stay on very long. Not enough current, and the flasher never flashes.

Suzuki stock flashers are made for big, high-powered signal lights. LED's just don't draw enough current (flasher is in series with the lights) to make the flasher work.

Most auto stores will carry flasher units for cheap. So long as it fits it should work. I would avoid the "heavy duty" ones as they may require a lot of current as well, causing the same problem.

As for attaching the flasher, I just used a small zip-tie.

Changing flasher easy. Installing permanent voltmeter, not so easy (If someone wants, ask for details).

Best of luck with those flashers!
 
Will the bulbs from the original blinkers fit in the new lights? If so they should work with the bulb swap.
 
Check all your grounds. Just because they are connected doesnt mean they are getting a good connection. Right after I got my GS it would have that problem at least once a day. id have to pull over and jam the connectors under the seat back together. Once I replaced the connectors, all was well. It could also be a dead flasher, or a blown bulb.
 
Make sure your battery isn't almost dead. My signals would flash once then stay on and I thought the flasher relay was bad, but the battery was just too low. Charged it up and it flashed fine.
 
No, its exactaly what JM_foote said. The LEDs just do not pull enough current. I am getting new front signals tomarraow, then I will get a new appropriotely sized flasher.
 
use an ELECTRONIC flasher, more expensive than standard, but does not depend on current draw to flash. put voltage to it and it flashes by itself.
 
You must log in or register to reply here.
Back
Top