Attention in the pits!!

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Guest

    #1

    Attention in the pits!!

    I had some headwork done on my 80 gs 1100 over the winter. 1mm oversize intakes & some porting, new seals & guides etc.
    I've been running a 18/48 sprocket combo on the street. I used the 18 to make sure I have enough clearance on the Bandit swingarm. I raced it last year & found I was shifting into 4th gear a couple of hundred feet shy of the stripe. I want to do a few drag race weekends this summer & am thinking of going to a 17/52 combo for the track.

    Thoughts? Advice?
  • Guest

    #2
    530?
    Curt

    Comment

    • Guest

      #3
      17 divided by 52 is .326. i am pretty sure that is Ray's formula... I am running 15/48 and am in fifth before the stripe by about 150 feet... might go to 16/48...
      The reasoning is closest to .320 usuall will get you within spitting distance...
      Curt

      Comment

      • Guest

        #4
        perfect, thanks.

        Comment

        • ozman

          #5
          18/56 gets you .321
          18/55 gets you .327

          Comment

          • rapidray
            Forum Guru
            GSResource Superstar
            • Oct 2006
            • 8195
            • So Cal

            #6
            Originally posted by ozman
            18/56 gets you .321
            18/55 gets you .327
            ACTUALLY.....18/56 is 3.11 & 18/55 is 3.05
            Divide the rear tooth count by the front count to get the ratio. You need to be around 3.20 to get the shift light on in high gear about 100-150 feet before the finish line in a quarter mile. You will need 57 or 58 teeth on the rear with an 18 front sprocket. I run 15/48 but mine is 630.
            Ray.

            Comment

            • blowerbike
              Forum Guru
              GSResource Superstar
              • Aug 2008
              • 7057
              • Ohio Closer to KY Than Cleveland

              #7
              Originally posted by nastyjones
              I had some headwork done on my 80 gs 1100 over the winter. 1mm oversize intakes & some porting, new seals & guides etc.
              I've been running a 18/48 sprocket combo on the street. I used the 18 to make sure I have enough clearance on the Bandit swingarm. I raced it last year & found I was shifting into 4th gear a couple of hundred feet shy of the stripe. I want to do a few drag race weekends this summer & am thinking of going to a 17/52 combo for the track.

              Thoughts? Advice?
              no bars?
              better gear it to go through in 4 not 5..could be a handful leaving the line..

              Comment

              • rapidray
                Forum Guru
                GSResource Superstar
                • Oct 2006
                • 8195
                • So Cal

                #8
                Originally posted by blowerbike
                no bars?
                better gear it to go through in 4 not 5..could be a handful leaving the line..
                Not a problem if he has a lock up & extensions on the Bandit arm. Strapping the front will help too.
                Ray.

                Comment

                • Guest

                  #9
                  Nope, no bars, no lock up, no strap, just a guy looking to do a few race weekends this summer. If 17/52 takes me to redline in 4th through the traps, that would be fine.

                  Comment

                  • blowerbike
                    Forum Guru
                    GSResource Superstar
                    • Aug 2008
                    • 7057
                    • Ohio Closer to KY Than Cleveland

                    #10
                    Originally posted by nastyjones
                    Nope, no bars, no lock up, no strap, just a guy looking to do a few race weekends this summer. If 17/52 takes me to redline in 4th through the traps, that would be fine.
                    that's how i set up a true street bike.
                    shift light on before the traps but not hit the limiter before the stripe in 4th.

                    Comment

                    Working...