• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

1977 GS750 Carburetors & petcock

  • Thread starter Thread starter janderson208
  • Start date Start date
J

janderson208

Guest
New to the forum, and first time GS owner. I have owned several Honda CB's but this is my first GS.

I have a couple things I could use some REAL GS knowledge on.

1. Fuel cock, PRI? Should the bike be run on PRI or no? How does it work?

2. Currently the carbs are set up as follows. Number 4 has vaccum hose going to fuel cock. Carbs 2 and 3 are connected with a vaccum line.
(left to right 1,2,3,4 as sitting on the bike) Is this correct? The manual I have is very unclear about this.

3. When I disassembled the carbs I removed the screws in the bottom closest to the intake manifold, the manual simply says " Do not adjust these" lol, what is a good starting point for these screws.

4. Are the above mentioned screws the "air screws" or are the air screws the ones on the airbox side pointing to 10 o clock.

I picked this GS up from a friend of a friend. The rims, spokes, forks and shocks look like the day they were made. The inside of the HUGE fuel tank is spotless. the clock shows about 6,000. It came with a Dyna ignition installed. I really like the bike and would like to get it running as good as possible.

Any help or suggestions will be appreciated.

thank you
 
The petcock is vaccuum operated that means that it will shut itself off if the bike isnt running. The PRIME position bypasses this need for vaccuum in such situations that cause the carb bowls to be dry..maintenace, rebuilding, ran totally out of gas even on resereve,,whatever. If the bowls are fully dry you put it on prime for maybe a minute to prime them. Once they are primed and the bike starts you put the lever to on and leave it alone unless you need the reserve. You can also disconnect the fuel line and run a piece of tubing from the tank to a can if you need to drain the tank for any reason by using the prime setting as well. The little nipple on the petcock is the vaccuum port. That hooks to the nipple thats between the number 2 and 3 carbs.. The other two higher nipples that are on carbs 2 and 4 are simply vents to stop vapor locking.
 
Last edited:
The bottom screw at the back of the bowls is the PIOLT SCREW.. This is set at 7/8 of a turn out from the bottom..seat all adjustment screws with care till they seat but you arent forcingbthem any further. The screws on the sides of the carbs just ahead of the slide towers are the AIR SCREW. These are set at 1 1/2 turns out. If the bike is stock the mainjet is supposed to be a 100 and the pilot jet is supposed to be a 15. the needle jet is a 5F21. The needle jet clip is on the center groove.. all that makes sense???
 
I editted the firt poat..the vaccuum port at the carbs that hooks to the petcock is between 2 and 3..not 3 and 4..the bottom nipples on each bowl are overflows. None ofthe vents or overflows get tied together as you said they were tied together now...
 
Last edited:
Greetings and Salutations!!

Greetings and Salutations!!

Hi Mr. janderson208,

See Where Do These Hoses Go? Your petcock gets its vacuum from the #3 carb. The tubes between 1/2 and 3/4 are for vent hoses. The fuel inlet is right in the middle of #2 and #3. You'll see a picture of CV carbs on my website. The hoses will be similar except for the placement of the vacuum feed on your VM carbs.


Let me dump a TON if information on you and share some GS lovin'. :D

I just stopped by to welcome you to the forum in my own, special way.
big_hi.gif


If there's anything you'd like to know about the Suzuki GS model bikes, and most others actually, you've come to the right place. There's a lot of knowledge and experience here in the community. Come on in and let me say "HOoooowwwDY!"....
hat1.gif


Here is your very own magical, mystical, mythical, mind-expanding "mega-welcome". Please take notice of the "Top 10 Common Issues", "Top 15 Tips For GS Happiness", the Carb Rebuild Series, and the Stator Papers. All of these tasks must be addressed in order to have a safe, reliable machine. Now let me roll out the welcome mat for you...

carpet.jpg


Please click here for your mega-welcome, chock full of tips, suggestions, links to vendors, and other information. Then feel free to visit my little BikeCliff website where I've been collecting the wisdom of this generous community. Don't forget, we like pictures! Not you, your bike! :D

Thanks for joining us. Keep us informed.

Thank you for your indulgence,

BassCliff
 
Thank you and just to be clear

Thank you and just to be clear

I now understand the petcock now. Thank you. By the way the bike does not have the original air box.

I am clear about the fuel feed line to the carbs as well as the bowl over flow lines.

Still uncertain on the small diameter lines running from the carbs at about the 10 o clock position.

I am certain the previous owner messed this up (since the wires for the Dyna were switched around as well).

Carb number 1 has no nipple at 10 o clock. Should there be a T installed in 2 and 3 of and then to the petcock?
 
The petcock hose is on the #3 carb on VM carbs. Check this photo below and note where the small hose comes off. These are VM22's but the hose on your carbs is similar.

Oh, and you need to rejet your carbs since it doesn't have the airbox.


Picture017.jpg
 
Thanks for the photo

Thanks for the photo

Makes pefect sense. Thank you for your help. I plan on rejetting and running high quality pods. The bike has a very very nice stock exhaust, but I also have a 4 into 1 with a vance and hines. On the honda inline 4's the 4 into 1 with aftermarket muffler sounds good (I think). Not sure what I'm gonna do on the exhaust side. You guys are great, thanks again.
 
IF you swap the exhuast for the 4 into 1s, may i have first dibs on the stockers? My 78m 750 E has a 4 into 1 thats not in very good shape. I am in the process of putting all my bikes back to stock and i would really like a shot at the 750 stock system.
 
You must log in or register to reply here.
Back
Top