• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

79 GS1000 starter not getting power.

  • Thread starter Thread starter dluszcz
  • Start date Start date
D

dluszcz

Guest
Bought a 78 GS1000E and discovered the engine was bad. Bought a 79 GS1000E motor complete with coils, starter, and wiring harness. It's been sitting since Thanksgiving. Anyway, I caved in and bought a garage heater and started trying to get it running today. Can't get anything to turn over. Check previous posts and checked all my connections, made sure they were good, and I still have no power to my starter. Can't even jump the starter. I was lucky enough to get my hands under the carbs to swap out the starters but no spark on either one. I bought this to learn how to work on bikes and I'm already stuck. Not sure what I have to or where else to begin. How can you check if a starter is bad? Any way to run new wires to see if it works? I do not have a battery installed as I used jumper cables hooked up from my car, which was not running. I just want to get the engine running for now and then I will put all the pieces back together when I start taping the deconstruction so I don't run into this situation again. Thanks.
 
Is your starter solenoid firing?

If I'm not mistaken, no solenoid movement = no power to starter. I'd imagine there is a way to jumper across the solenoid to check the starter.

Dre
 
First check to see if you have 12 volts at the solenoid post that goes to the positive battery post. If you do, then make sure you have 12 volts at the yellow/green wire when you press the starter button. Check back after you look at these things and let us know what you find.

I just re-read your post. We can offer help easier if you put a few paragraphs instead of one big block of text.

I would break down and buy the correct battery and install it. Jumpers will just add more connections and confusion when troubleshooting.
 
Last edited:
If you have power to the solenoid and a good battery jumping the solenoid should of turned the starter.
You can check the starter with a set of jumber cables and a car battery. Put the positive cable on the stud where the positive battery cable hooks to and ground the starter at the round nub at the end of the starter.
 
The silly question might be the answer. Because I bought just the motor and all in a frame that can't be titled, I figured that if I hook up the gauges and make sure it's in neutral that it would start. I have a green light on the neutral switch and everything else, but didn't even think about pulling the clutch. Could it really be that simple? I hope so. Thanks for the advice to all. I'll give it a shot later and report later.
 
dluszcz said:
I have a green light on the neutral switch and everything else, but didn't even think about pulling the clutch. Could it really be that simple?
Click to expand...
Yes, it might really be that simple. Suzuki wired a switch into the clutch lever as a "safety" feature, to prevent starting the bike if you happened to leave it in gear, forcing you to disengage the clutch to be able to use the electric starter. That way it does not matter if it's in gear or not, it will be "safe" to start.

Many of us have bypassed that switch so it's not necessary to pull the clutch, but you have to be sure that it's in neutral before pushing the starter button. :o

.
 
Well, no luck yet. Maybe because I don't know exactly what I'm doing, I can't figure it out. Going back to basics. So, I took a picsof what I think is the starter. Not sure since I thought I had it all figured out and I'm 2nd guessing everything I've done. I have it installed but now I do not believe I've been testing it correctly and I do not think I have power going to it. I have the black cable that mounts to the outside of the starter(?) going to the frame of the bike right now. The green and yellow wire is still attached to the solenoid. Should there be power there?
 
The threaded post on the starter goes to one threaded post on the solenoid. The other big threaded post on the solenoid goes to battery +. The green and yellow wire gets a momentary +12v when the starter button is pushed.

You should be able to attach +12v to the starter post and ground the case to see if the starter motor turns.
 
OK. Now I am thoroughly confused. Is the picture I attached the starter? And, the solenoid, I can only see where the green/yellow wire snaps on. There are 2 bolts that I can removed but I do not see any other wires. Do I need to removed those 2 bolts to see the other wires? Even when I press the start button and I have the tester light on the green/yellow wire, no power.

I am not that mechanically inclined yet and I'm just looking at the internet and the Haynes manual (which doesn't show much). That could be 1 of the problems right there.
 
OK, just jumped the starter solenoid. Got the spark but no turn. What does that mean?
 
I think if the polarity is reversed it will not turn. To you make sure you had positive on the post? If you did, than the starter may be toast.
 
Starter is good. Apparently I can't follow wires too well when they are buried. I had the grounds mixed up. Switched them and just jumped the starter.

I even tried getting it running by jumping the starter. Poured a little fuel in the line to the carbs and tried to get it started but no luck. At least I got it to crank and that was my goal.

Any way I can figure out why I can't get it to turn over by pressing the button? I pressed the clutch in after hooking up the cable again and nothing. No power to the green/yellow wire either.:-k
 
You must log in or register to reply here.

Similar threads

P
Starter cranking slowly
Replies
7
Views
145
adam83
adam83
oldGSfan
Something hinky with GS1100E starter or starter clutch?
Replies
16
Views
355
oldGSfan
oldGSfan
E
Electrical gremlins affecting indicator lights and starter circuit
Replies
9
Views
219
eldevigo
E
O
Did I just fry the starter motor?
Replies
5
Views
160
oldsecret
O
R
79' GS550 Will run on starter fluid but die after a few seconds
Replies
11
Views
256
Cipher
C
Back
Top