• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

A diagnostic challenge

  • Thread starter Thread starter flyingace
  • Start date Start date
F

flyingace

Guest
There are three of us with the same year/model (1983/GS850) with an identical problem. The bike runs fine for a while with a new plug, then the #4 spark plug gets black and sooty and the bike idles poorly and stutters coming off idle. The problem follows the #4 cylinder after swapping the #1 and #4 plug wire and plug. It happens to new plugs as well as old.

Between the three of us, we have gone thru the ignition system, cleaned&synched the carbs, checked the intake manifolds - just about everything we can think of. It is always the #4 cylinder on all three bikes.

Does anyone have any ideas what it can be? If not, heard of anything similar involving a particular year/model.

Thanks in advance,
Ace.
 
thats odd, maybe one of the grizzled old vets knows of something, but offhand Id say I cant think of any one unique thing with the #4 cylinder that would make it any more prone to foul than any other.

but it sure is an odd coincidence that 3 identical bikes have identical problems.
 
LW,
Thanks. Something just occured to me about this. I wonder if it's possible the #4 carb's choke is not getting turned all the way off. Since it's at the end of the bank of carbs, if the mechanism that shuts the choke off was placed too far left (or right?)...

This would explain why cleaning the heck out of the carbs doesn't help.

I may try removing #4 from the choke circuit.

Ace.
 
Re: A diagnostic challenge

Did the same person tune and synch all three bikes or give instructions to the other two?

Earl


flyingace said:
There are three of us with the same year/model (1983/GS850) with an identical problem. The bike runs fine for a while with a new plug, then the #4 spark plug gets black and sooty and the bike idles poorly and stutters coming off idle. The problem follows the #4 cylinder after swapping the #1 and #4 plug wire and plug. It happens to new plugs as well as old.

Between the three of us, we have gone thru the ignition system, cleaned&synched the carbs, checked the intake manifolds - just about everything we can think of. It is always the #4 cylinder on all three bikes.

Does anyone have any ideas what it can be? If not, heard of anything similar involving a particular year/model.

Thanks in advance,
Ace.
Click to expand...
 
No. I started a thread about this problem a while back. Since then, 2 other users in different parts of the country have written to describe virtually the identical problem with their 83 850.
 
Considering what you said you've already done, I would check compression, valve clearances, the seal on the rubber plug on the jet in the float bowl and the float height setting.

Earl


flyingace said:
No. I started a thread about this problem a while back. Since then, 2 other users in different parts of the country have written to describe virtually the identical problem with their 83 850.
Click to expand...
 
Thanks Earl.
The compression on my bike is low - but #4 is the highest of them all (128). Also, I seem to recall the compression readings from the other users were better than mine. The float height is OK on mine, and I think the others checked that too. I don't remember a seal/rubber plug on the jet. I'll look again next time I'm in there.

I think my next step is to remove #4 from the choke linkage and see if the condition improves. If not, then look into swapping #3 and #4 carbs to eliminate or identify the #4 carb as the problem.

I think this is some kind of marginal factory defect that doesn't show itself until the bike is old and tired.
 
On my bike, I cant swap the #3 carb with the #4 carb. There are fuel fittings on #3 on both sides. On #4 there is only a fuel fitting on the left side of the carb.

Earl


flyingace said:
Thanks Earl.
The compression on my bike is low - but #4 is the highest of them all (128). Also, I seem to recall the compression readings from the other users were better than mine. The float height is OK on mine, and I think the others checked that too. I don't remember a seal/rubber plug on the jet. I'll look again next time I'm in there.

I think my next step is to remove #4 from the choke linkage and see if the condition improves. If not, then look into swapping #3 and #4 carbs to eliminate or identify the #4 carb as the problem.

I think this is some kind of marginal factory defect that doesn't show itself until the bike is old and tired.
Click to expand...
 
That's disappointing news, Earl. I'm sure mine is the same now that I think about it. I may try to jury-rig something temporary that will get fuel to all the carbs just to help diagnose this problem.

Are there other differences you can think of between #3 and #4 carb?

Thanks again,
Ace.
 
ON bikes with CV carbs, the #3 carb is normally the control carb for a carb synch. #3t has no vacuum adjustment. #4 is adjustable.

Did you already synch your carbs using vacuum guages connected to all 4 carb simultaneously? A manual synch will not do and neither will trying to set vacuum levels with moving a single guage back and forth.

Earl


flyingace said:
That's disappointing news, Earl. I'm sure mine is the same now that I think about it. I may try to jury-rig something temporary that will get fuel to all the carbs just to help diagnose this problem.

Are there other differences you can think of between #3 and #4 carb?

Thanks again,
Ace.
Click to expand...
 
Yes, I used a Motion Pro carb synch tool. It shows all 4 readings at once. All vacuum readings were within 1/4 MM/Hg of each other. The other users all synched their carbs too.

I'll just have to look into how difficult a chore it will be to swap carbs (if it can be done at all).

Thanks again Earl.
 
its possible someone may have broken off a needle and drilled out a pilot jet, but it seems odd that it would happen to three people at a time.

Earl



flyingace said:
Yes, I used a Motion Pro carb synch tool. It shows all 4 readings at once. All vacuum readings were within 1/4 MM/Hg of each other. The other users all synched their carbs too.

I'll just have to look into how difficult a chore it will be to swap carbs (if it can be done at all).

Thanks again Earl.
Click to expand...
 
Hi all.
I am one of the trio that has had this problem of rich #4 cylinder. Flyingace and myself have been discussing it via email in the hope that we could jointly solve it.
Well, I have just today solved the problem on my bike and its now running perfectly from idle to redline. All plugs are nice and clean for the first time since I got the bike, so I am well pleased.

The problem was finally traced to a "loose" pilot jet.

After taking the bowls off the carbs and removing the black rubber plugs from each pilot jet passegeway, I measured the depth of each pilot jet from the lip of the passageway. #4 was about 2mm higher than the others - thats about one complete turn of the jet !

Maybe the thread on this carb was damaged when I first removed the pilot jet for cleaning ? Anyway, all it took was one turn with the screwdriver and the jet was properly seated.
Its hard to believe that this tiny adjustment cured the problem, but I guess it just shows how sensitive these pilot jets are.
 
Nick,
Congrats on finding this out! Wouldn't it be weird if some guy in the Mikuni factory was just goofing off one day in 1983 and just didn't screw in the pilot jets of a bunch of carbs! :D

I'm wondering if we have the same carb types - you being from the UK and all. Are yours the 32mm Mikuni CV type? I just don't remember any rubber plugs covering any jets or passageways. But I was only inside the carb once, so I could have missed it.


Ace.
 
Ace,
Yes, they are the 32mm Mikuni CV carbs.
I think the loose pilot jet may have been my fault as I remember that it was difficult to remove when I first dismantled the carbs for cleaning.
I may have scored the thread and this would have caused the bad seating problem.
However, these carbs bodies are incredibly complex and I did wonder if there may have been a tiny fault in the casting that resulted in the pilot jet being a tight fit. Just a thought !
Anyway, it would be interesting to see whether your problem is the same as mine.

Nick
 
You must log in or register to reply here.
Back
Top