• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

About to rewind my stator

  • Thread starter Thread starter Anonymous
  • Start date Start date
A

Anonymous

Guest
I am about to rewind the stator on my '78 GS1000C. I have read the stator papers, unwrapped the stator wiring (Ugh! Pretty burnt and ugly. No wonder it didn't work), counted the wraps, purchased the magnet wire (only $5) and have a pretty good idea of how to go about it. I didn't know where to get the heat resistant epoxy that the Maynards recommend, so I asked the guy that sold me the wire what they use. He thought that the choice of epoxy was rather odd and told me that they just dip the wraps in varnish and bake it to harden it. He also told me that the magnet wire already has an insulating coating on it to keep it from shorting out and that the baked varnish dip is to keep the wire wraps from vibrating and wearing through the insulating coating.

So, my question is: Has anybody else done the stator rewind and what did you use to coat the wraps? My own experience with epoxy is that it softens up when you heat it. However, it may stiffen after it has had a chance to bake and cure further. I've never taken the observation that far.

Any suggestions would be much appreciated!!

Blaine :D
 
I have never done it but the epoxie is to protect the stator from vibration and from the hot oil. I would sugest wearing gloves, be very careful not to kink the wire and wrap it tightly As with any unfimaliar repair go slow and take your time
 
I did mine may years ago (20 I think). Used slightly larger wire and no epoxy. It is still in the bike now. The epoxy may stop vibration problems, but would also stop the oil cooling it. I have run an oil coler since that time, and I think this leads to mechanical longevity.
 
On reading this I remembered a can of paint I have had for years....dug through never-never land, aka basement) and found it. A number of different products are made by the same company, but they used to be about the top name for insulation on windings. I haven't done any winding for about 40 years, so I didn't know if it was still applicable.

My old can shows made by Canadian General Electric, but you can go directly to the US website for more info.

Go to www.glyptal.com and look around.


Look for product 9620....intended for use on stators, and good in oil up to 130C/265 F

They also encourage you to contact them directly for advice, and even state you will reach a chemist who will not try to push you into buying something, but will help you with your problem. :)
 
Thanks for the advise guys! At the moment I am inclined to use the varnish, mostly because it is easier to obtain. I may even have some in the "swirling vortex" of my basement. My concern is that it may break down at higher temps.

The other question I will pose is: Should I remove all of the old coating from the stator (after the wraps are removed) or can I get away with putting the new wraps over the old coating?

Blaine
 
The coating on there is permanent insulation. leave it on, but get rid of the loose particles
 
Hey Junkman,

Sounds like a good project.

I did the same, about 6 mos ago. I peeled as much of the coating off of the core as would easily peel off. I got the wire from a local guy who does motor windings. The wire was pre-coated with a baked on finish. Then, once it was wound, I coated the windings in a high-temp epoxy that I found at my local hardware store.

A note of caution: after you've coated with epoxy (or whatever coating), and are letting it harden, be sure to restrict the loose wires such that they go where you want them to go. :oops: I didn't, and had to use some brute force to fix it!

However, it is working just fine.

Best of luck!
mike
 
You must log in or register to reply here.
Back
Top