• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

Any tricks to getting old valve cover gasket off?

  • Thread starter Thread starter Joel750T
  • Start date Start date
J

Joel750T

Guest
Any tricks to getting old valve cover gasket off? I have about 80% of it off fine after my first try at a valve adjustment (not bad at all thanks to the docs!), rest is bonded in.

Two credit cards and a bandaid down so far..
 
I use a razor blade to do mine. Just need to be careful not to gouge any grooves into it. Might try to wt it down with some oil or WD40 to help loosen it.
 
Removing the old gasket is by far the worst part about performing a valve adjustment. Permatex sells a gasket remover spray that will help soften the gasket, but that only helps, it does not make the job easy. Spray the sauce in a cup and then dab it on with a paint brush or similar. The gasket remover will eat off paint so keep it from dripping on your engine. Paint stripper also works pretty well to soften the old gasket. Sucky job but one that must be done so take your time and don't hurry.
 
Get a shallow baking pan, big enough to put the valve cover in. Put about 1/4 inch of water & dish soap in it & put the valve cover in the pan with the gasket in the water. Overnight or a whole day should be enough to do the trick on it. Then just scrape as needed. Ray.
 
Yea, hopefully the gasket is stuck to the valve cover instead of the engine. Ray's trick is a good one if it is.
 
Please understand, this is a bit tongue-in-cheek -- The best trick on removing a valve cover gasket is to install it correctly in the first place. ;)
You have been offered several good solutions to remove it. Your real problem (IMHO) was the manner in which it was installed in the first place.
When you finally get the new one (OEM I hope) install it dry, or with a bit of grease for keeping things lined up. Then when you go to remove it the next time, you won't be confronted with this issue again.
Best of luck.
 
Thanks all, I appreciate it. Got it off, fortunately, it was all on the cover, not the engine. Found some other sites before I got a response here and saw some people mention wd40 so I gave it a shot and it worked fairly well, along with a thick bladed putty knife I had. Sprayed the new one down with WD40, fired right up, no leaks. Job not so bad..
 
This is probably the carpenter in me; but I always use a piece of oak or any scrap hardwood I have in my bin. I'll cut at least a 45 degree bevel on it and scrape away without any worry of gouging the aluminum. Only takes a trip to the miter box to sharpen as necessary.
 
You must log in or register to reply here.
Back
Top