• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

Bad Coil?

  • Thread starter Thread starter waynek
  • Start date Start date
W

waynek

Guest
My specs...1979 GS1000L 31K
The Problem- When I take off the plug wires to either #2 or #3 (wires coming from the same coil) the engine runs with no change...so it's only running on 2 cyls...there's no spark from coming from 2 or 3???
Does this sound like a bad coil? they look like the stock coils
thanks in advance
 
Could be bad coil. OR, could be you have no B+ ignition power to feed the suspect coil. OR, could be a problem with the points circuit for that coil. Like shorted wire, point set that don't open, point set that doesn't close bad condensor. OR, could be a problem with the spark plug wires themselves, or even (2) shorted spark plugs.
 
Bad Coil?

I recommend that you remove the questionable coil and take it to your local motorcycle/automotive service dept. and ask them to check it using a coil tester. I am convinced resistance readings are not sufficient measurements to determine if a coil will work under load. I found a local motorcycle dealer that tested two coils for me at no charge, both coils were bad although resistance readings were not too far from spec. The parts dept ordered OEM coils (for my 1982 GS450TXZ) and I had them within 3 days.
 
If you're still running a points ignition you could have a bad condenser or point gap has slipped.
 
I had the bad suspect coil tested and it's dead. now I'm wondering how long I've been running with 2 cyls....
 
On my '82 GS850L I replaced both coils with high output Accell coils, new wires, caps & plugs, as well as changing out the old ignition with a new Dyna S as ignition pickup signalling the coils was suspect. I don't know if you're bike has electronic ignition like mine, but that swap gets me plenty of good, strong spark now.
 
chef1366 said:
Switch the coils and see if the problem follows.
Click to expand...
Good advice here. Switch the supply wires to the coils and if the plug wires will, reach you need to switch the inner two to the outside cylinders and the outer two to the inside. This will let you know if it is the coil or further back in the ignition.
 
Experiencing no spark in just ONE cylinder

Experiencing no spark in just ONE cylinder

I just successfully put fixed leaky carbs on my 79 GS550 (thanks to help and advice from several of your posts, it started up rebuilt on the first crank), and now I'm having a new problem - no spark in one cylinder. First I'll try swapping wires, but what's the next diagnostic step after testing the wire when only one cylinder isn't firing? Ground? Points?

I too wonder how long I've been riding around on three. The bike had a surprising amount of power and ran very smoothly.

Does riding around on less than four cylinders do any damage to the engine? My last few long rides last season it felt a little sluggish. But I'm easy on my old girl, so I guess I didn't really notice the power loss. I may have put a few hundred miles on it, blowing off the occasional pop or miss, riding on three cylinders.

Thanks for listening. -Bryan
 
Check your spark plug wire lead. Screw off the plug cap and cut a little off the end of the wire till you see nice shiny copper and screw it back on.
 
You must log in or register to reply here.
Back
Top