• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

clarification on front brake piston

  • Thread starter Thread starter Anonymous
  • Start date Start date
A

Anonymous

Guest
I have read a few things that seem to conflict and would like some clarification.

I have been having problems with my front brakes holding and not releasing. I cleaned the relief valve (lots of sediment), but still have problems. I was going to take apart the front calipers and clean out behind the piston. I can imagine that there would be lots of junk there. I have also read that the O ring channel may be filled up with gunk pushing the O ring out on the piston, and binding the piston wherever it may be.

My question is about removing the piston. I have read that to remove it you can use the brake fluid to pop it out while the caliper is removed from the bike, but still atttached to the brake line. To do this you just pump the brake. I have also read never to pump the brake handle when the caliper is not installed on the bike, but the break line is still connected.

So can I remove the caliper piston by simply pumping the brake while caliper is not installed, but still attached to the brake line? Or will this cause damage? Thanks.
 
You can remove the piston that way without damage to anything in the brake system. The reason they say don't pump the brakes with the caliper off is because most people will be only changing their brake pads and having the pistons pop out would not be something they would want.

Hap
 
Brake Piston

Brake Piston

Hello U can use compressed air once u remove the caliper from the bike. BUT use low pressure it will come out with some force but no damage will occur if ur carfull. The O ring may B damaged causing the piston to bind. If u must clean up the piston surfaces U can use 1500-2000 grit water sandpaper using oil in place of water, This wil restor them to new condition. Remember to lube the caliper with brake fluide when installing the piston.
Best of luck! Archei
 
pump away

pump away

The reason it's said not to pump the handle while the caliper is removed is so you don't unintentionally pop out the piston. it's the best way to remove it. Be sure to have a container handy to catch the fluid, once the piston pops out of the bore it'll start running.
You can use air but you have to be careful the piston doesn't fly out.
Whatever you use to clean things out make sure it's compatale with the seals, use the wrong chemicals and you're up the creak.
A friend of mine worked at Canadian Tire and a car lord of kids came in complaining their brakes were not right. Upon further questioning he found out they had used engine oil instead of brake fluid. When he took the top off the master cylinder the rubber gasket looked like a stringy lump of snot. Ended up replacing all the rubber components of the system.....Mike
 
Brake Piston

Brake Piston

Hello U can use compressed air once u remove the caliper from the bike. BUT use low pressure it will come out with some force but no damage will occur if ur carfull. The O ring may B damaged causing the piston to bind. If u must clean up the piston surfaces U can use 1500-2000 grit water sandpaper using oil in place of water, This wil restor them to new condition. Remember to lube the caliper with brake fluide when installing the piston.
Best of luck! Archei
 
Brake Piston

Brake Piston

Hello U can use compressed air once u remove the caliper from the bike. BUT use low pressure it will come out with some force but no damage will occur if ur carfull. The O ring may B damaged causing the piston to bind. If u must clean up the piston surfaces U can use 1500-2000 grit water sandpaper using oil in place of water, This wil restor them to new condition. Remember to lube the caliper with brake fluide when installing the piston.
Best of luck! Archei
 
Brake Piston

Brake Piston

Hello U can use compressed air once u remove the caliper from the bike. BUT use low pressure it will come out with some force but no damage will occur if ur carfull. The O ring may B damaged causing the piston to bind. If u must clean up the piston surfaces U can use 1500-2000 grit water sandpaper using oil in place of water, This wil restor them to new condition. Remember to lube the caliper with brake fluide when installing the piston.
Best of luck! Archei
 
brehill, be very careful if you use an abrasive to clean up the piston or the bore. On a typical bike like my 1000, the service wear limit is (-) or in other words, the piston and bore must remain their original sizes. Don't even remove .001" For light cleaning, you might want to try Blue Magic or Semi-chrome polishing paste. This works well for polishing carb slides and bodies. I think the pistons will just pump out, but I've always used compressed air. Be sure to use a rag so the piston can't hit anything and get scratched.
If you have the chromed caliper axle bolts, corrosion of the chrome plating can cause the calipers to not slide back and forth smoothly. They also have o-rings and need a special grease, according to Suzuki.
 
You must log in or register to reply here.
Back
Top