• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

Clutch not disengaging GS300

  • Thread starter Thread starter Pigthang
  • Start date Start date
P

Pigthang

Guest
Trying to get this bike back up to par after sitting for unknown amount of years. I think the clutch plates maybe stuck together and the clutch lever is very difficult to pull in even after lubing. any ideas?

Did a clutch adjustment according to the manual and nothing worked. should I open the right side case and see if they are stuck together and if so pry them apart?

I do not know much about Jap bikes since I've only work on my old harley, but being they are two different beasts I want to see what you guys would do first.
 
You may find it just needs to be warmed up/ridden a bit to free them up...
 
Definitely open up the clutch cover and have a look at the disks. You can do this without draining the oil if you leave the bike on the sidestand and not the centerstand.

Dollars to donuts, they are glomed together. Since you are in there you can measure your springs, check the thickness of your fiber disks and check all the disks for "trueness" by laying them flat on a pane of glass. That will show if any are warped, which would ,of course, necessitate changing out. Have a look too at the "tangs' (teeth) of the basket for any signs of gouges on the inner surfaces which can hang up the disks. You can file smooth any you find. Relube each disk with frsh oil as you reassemble.

Once it is all back together, but before you put the cover on, adjust your cable and check to see the disks "part" as you squeeze it in. If they all move apart smoothly, you are good to go.

Good luck with it.
Spyug
 
Take the rubber plug off the side of the engine down by the shifter. squeeze the clutch and see if that silver screw moves at all. If not then it is likely your clutch cable needs to be serviced or replaced.
 
razor02097 said:
Take the rubber plug off the side of the engine down by the shifter. squeeze the clutch and see if that silver screw moves at all. If not then it is likely your clutch cable needs to be serviced or replaced.
Click to expand...

It does move but it also pushes out the cover a tiny bit when the cable is pulled. I'm going to order a new cable anyways since this one is fraying at the handle.

And thank you for the advice. I'll post back once i have time to check the clutch basket.
 
Its pushing on the cover? :eek:

Have you taken the cover off? You will need a 10mm wrench and an 8mm socket. There could be some sort of debris in there preventing the clutch rod from actuating or the clutch rod itself isn't seated somehow. Also take us along on your adventure with some pictures it will help us help you :)
 
clutch springs

clutch springs

it's definitely the clutch springs. I took the plates apart wiped the fibers and removed the corrosion on the steel plates with some scotch brite pads.

The plates and steels are all in good condition but the clutch springs are measuring in at about 30.5mm each and the manual says the service limit is 33.x

I pulled the clutch lever in while the springs where out and it travels freely and doesn't feel like it's got debris in the way.
 
You must log in or register to reply here.

Similar threads

roy826
New clutch in my 1982 Kat 1000
Replies
17
Views
192
first timer
first timer
E
Stuck clutch - oil issue?
Replies
12
Views
226
tobaccorancher
T
D
4th clutch cable in 10 months
Replies
3
Views
89
Nessism
Nessism
bobtail84
Starter Clutch Upgrade
Replies
5
Views
115
dgates1
dgates1
dgates1
Carb choke rail lever needed...
Replies
11
Views
157
dgates1
dgates1
Back
Top