• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

clutch pushrod should be screwed in or out for cover install

  • Thread starter Thread starter Anonymous
  • Start date Start date
A

Anonymous

Guest
82 gs450t im new, clutch cover/chain cover off to clean out everything since the clutch cable was sticking. I also messed with the clutch rod it spins easiliy between my fingers. Im just wondering how far it should be screwed in or out when i put the cover back on? Screwed all the way out? all the way in? in the middle? thanks! also i was just told that the clutch cable should just push it in and the gizmo in the bottom picture doesnt spin it. but when i put the bike in first gear and push the rod in, i cant push the chain sprocket. and when i pull it out 1/4 inch i cant turn the chain sprocket either. when i unscrew the rod out 1 inch until it stops i still cant spin the chain sprockt. When the rod is screwed in i can snap the rod back and forth with my pinky toes 1/4 inch so is the gizmo supposed to push the rod in with the rod being pushed into the engine housing its farthest? cause i grabbed the rod weith vice grips and tried pushing it in farther and no go. so im stumped.

but heres the clutch rod
mini-rodwithnothreads.jpg

[imghttp://img12.photobucket.com/albums/v31/Scoutsmommy/mini-insideofgizmo.jpg[/img] and here is where it goes no threading on either end. I dont understand how this works cause i can pull the rod out about a 1/4 inch and it will stop but then i can turn it counterclockwise and it will start spinning the rod out about an inch and there it will stop.

Anyone have the little clip that is held on by a screw and it slides over the choke rod and the choke lever moves the pins on the sides of the carbs up and down? i need one.
 
The clutch pushrod is a slider and is meant to move back and forth. There is no screw in or rod placement adjustment. Pushing on the end of the rod disengages the clutch plates as long as the rod is pushed in. If you cannot rotate the countershaft sprocket, then the bike's transmission is in gear. This would have nothing to do with installing the engine /countershaft cover. On bikes with a through the case clutch pushrod (as yours), on the outside of the clutch cover/case. you will see probably a small round coverplate with three scres holing the plate on. Under that you will find a slotted machine screw and a jamb nut. After the cover is installed, loosen the jamb nut and turn the slotted screw until you feel no tension on the screw. Then turn the screw down until you feel it just stop/make contact. Then back the screw off about 1/2 turn and tighten the jamb nut so the screw cannot change setting. Clutch free play adjustment is then made with the knurled adjuster at the clutch cable on top of the side cover/case and at the knurled adjuster at the handlebar.

Earl
 
thank you!

thank you!

thats just what i needed to know! the little slotted screw cover has 2 screws in it for future reference. any idea how to adjust the clutch free play?
 
Clutch

Clutch

The best way to adjust the clutch free-play is to add slack at the clutch lever by loosening the big fat round "wheel" and then turning in the small hand "wheel". This will create slack throughout the length of the cable. Next, loosen up the retaining nut where the clutch cable enters the case (surrounded by a rubber casing) and adjust the nut next to it in order to take up most of the slack (that you created at the lever).

Make sure you leave a little slack so that the clutch won't be partially engaged. When you finish that, make any necessary final adjustments at the clutch lever and you're ready to go! :!:
 
You must log in or register to reply here.
Back
Top