• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

Coil test

  • Thread starter Thread starter Thomas Kenny
  • Start date Start date
T

Thomas Kenny

Guest
1984 GS550ES

A couple of weeks ago, my bike began struggling to run and now will not start. I've got fuel but not a real strong spark. I checked my signal generator pulse pickups and the book calls for 250-500 ohms. They each read almost 400 ohms so I should be OK. I just did an igniter test and I am getting spark but not a strong spark. I tested my coils. They are marked 12v 3. I am assuming that the three is for 3 ohms. I tested both coils on my ohmmeter and am getting a reading of 2.3 ohms.

Should I be getting a strong 3? Do I need to replace my coils? Where is a good place to get some replacement coils and high tension leads if I need to replace them?

Any help appreciated. Ta Ta, Tom
 
Check the voltage that is going to the coils with the ignition on but the bike not running. If you have less than 11 volts going into the coils that may casue a weak spark. Often times people replace coils, but it's the crazy wireing that Suzuki engineered that is to blame. The power feed for the coils goes from the battery, to the ignition, back to the fuse box, to the headlight bucket, to the right bar switch, back into the harness and out to the coils. Many folks install a relay with power coming directly from the battery.
 
Ok, I couldn't wait Jethro, I measured the current and the right coil is a solid 12 volts and the left is approximately 11.2. I need to get a digital volt/ohmmeter :-D So real slooowwww, how do I set up a relay between the battery and the coils. Will this keep the coils hot with ignition switch off? I am not afraid to play with electrical, but being technically stupid, on the sparky stuff I don't want to fry myself or the bike. So I've got two leads to each coil from the harness and?

Your insight is welcome.........
 
11.2 volts will not casue the coils to have weak spark. Your problem is either with the coils or something else.
 
Thanks, I am thinking perhaps the coils or high tension leads are breaking down after 22 years, so I am going to look for replacement coils and leads as everything else seems to be working.
 
have you thought about a tune up???
new plugs may be the way out of this jam...
 
Thanks DaShadow, I just put new Irridium plugs in the bike and they read good. My bike has done this a couple of times before for no good reason after running like a champ, and number four has been intermittent when warming up. After testing the spark at the plugs several time # four sometimes does not fire. When I wiggle the connections to the coil that fires number 4 and give the coil a good whack :-D It will spark and then quit again. I took of the high tension cap from the lead and cut about 1/8 inch off of the lead and screwed the cap back in but it still is an on an off thing. So I think I will look at buying new coils and leads since everything else checks out ok. Just need to find coils and leads that aren't gold plated :-D
 
You must log in or register to reply here.
Back
Top