• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

cylinder head cover

  • Thread starter Thread starter goggleboy
  • Start date Start date
G

goggleboy

Guest
I dread taking my cylinder head cover off every time....
After removing all 16 screws or 18 cant remember... I need to remove the side caps in order to take off the cylinder head cover.
I freggin' bent and twisted an allen wrench trying to get my cap screws off.
All the screws on the two left caps are stripped, and the caps on the right only got 1 screw taken from each. As I was trying to break one of the screws free a huge snap and spark came about...the wrench went flying across the garage. :eek:
How do they get so tight? heat/cold? Now I had to pry my cover off with the caps still on, and I am stuck with a cover and caps with stripped screws.
Any way avoid this? the screws for the side caps are a little unique I know, but, different screws?
 
Last edited:
To address the immediate problem, drill the screws off with a cobalt drill bit. If you're careful, you shouldn't ding up the caps.

For future reference, use a high-quality allen wrench if they're allen head screws -- the low-dollar tools don't fit right in smaller sizes and they strip and break.

If they're still phillips head screws, use an impact driver or JIS screwdriver (you can order a set of JIS screwdrivers from McMaster-Carr for not much dough) to remove them. Japanese (JIS) screws have a very slightly different profile than standard American phillips, which leads to lots of stripped screws and heartbreak. Remove them with the proper tools, then discard and replace.

You should also install new screws with a bit of LOW-STRENGTH thread locker. (This is usually purple, and can be a little hard to find.)

Red or blue thread lock are too strong. And if you install these screws dry, they can seize up, especially if they are stainless steel. Essentially, stainless will eventually weld itself to aluminum unless there's something like antiseize or thread locker in the way.

Although you haven't revealed which model you have, most 8 valve GS models use M5X12 flat head screws here.
 
I agree with everything Brian has said, if by some chance you have a GS650 then the process is completely different. It's an idea to put the model of your bike in your signature line so we know what model is specific to your questions.
 
You must log in or register to reply here.
Back
Top