• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

Fofk shimming article

  • Thread starter Thread starter The Doktor
  • Start date Start date
T

The Doktor

Guest
Many years ago, there was an article in, I believe, Cycle magazine or possibly Motorcyclist, about how to shim the bushings and other tricks to minimize stiction in the forks of the GS 1000 & 750 series bikes. I could swear I've seen a copy of it somewhere in the forum, but I can't find it. I've searched the archives, but no luck. Any help out there?
Thanks.
:confused:
 
I remember that article. I used strips cut from an aluminum can behind the fork bushings and it really made a huge difference on my '84 Kawasaki 900 Ninja.
 
If i wasnt cleaning up ill have a look at my old mags for the article. They where using feeler gauge strips to "shim" the lower fork bush to take the slop out.
 
tkent02 said:
Can you explain this a little bit?
Click to expand...

Sure. On my Kawasaki, there are bushings positioned on the inner fork tubes at the bottom. They are secured to the inner tubes in channels and the outer tube rides on them. They look like small tubes about an inch long and are constructed so they can be opened enough to be removed from the fork tube once you take the forks apart.

View attachment 3906

It is at the bottom of the framed area in this parts fiche diagram.

The forks were slightly sloppy even after fitting a fork brace, so, following the article, I removed the bushings and shimmed them by using a strip cut from a soda can. This, as luck would have it, was perfect and tightened the forks up beautifully.
 
1980GS1000E said:
Sure. On my Kawasaki, there are bushings positioned on the inner fork tubes at the bottom. They are secured to the inner tubes in channels and the outer tube rides on them. They look like small tubes about an inch long and are constructed so they can be opened enough to be removed from the fork tube once you take the forks apart.

View attachment 3906

It is at the bottom of the framed area in this parts fiche diagram.

The forks were slightly sloppy even after fitting a fork brace, so, following the article, I removed the bushings and shimmed them by using a strip cut from a soda can. This, as luck would have it, was perfect and tightened the forks up beautifully.
Click to expand...

So the shim goes inside the bushing expanding it and makes the clearance tighter?
 
If I recall correctly there were two parts to this mod. One involved shimming one of the bushings (lower?) and the other involved dimpling the other (upper?) bushing with a punch to effectively increase it's thickness. I remember doing this mod to my '83 GS1100 in the basement of a house I rented in '85 or '86. The article would have been in Cycle, Cycle World, or Motorcyclist magazine. The guy who came up with the procedure was Pierre DesRoches, I believe.

Thanks,
Joe
 
Yeah - chiphead posted the link to a copy of that article I put in awhile back. It works well.
 
Fork shimming article

Fork shimming article

Thanks everyone. I did this years ago when I did a restoration/upgrade on my 78 GS1000, and it does indeed work. I need to get into the forks of my vintage Husky race bike this weekend, so I wanted to be prepared. The shim stock (12" long) is readily available at industrial supply stores like Fastenal, in case anyone else is interested.
We motorcyclist lost someone very special when Pierre Desroches died in the helicopter crash. He was a very innovative tuner, mechanic and writer.:-D
 
You must log in or register to reply here.
Back
Top