-
Required reading for all forum users!!!
Welcome!
Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.A note to new registrants...
All new forum registrations must be activated via email before you have full access to the forum.A Special Note about Email accounts!
DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.A note to old forum members...
I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.
Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...
-
Returning Visitors
If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.
If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.
Well, be sure to check that the float bowl vent lines are clear and not kinked. Test by blowing into the lines so you know air enters the bowls. You shouldn't need to blow real hard. Only problem here is that each line supplies venting to two carbs. So blowing into each line (with the carbs assembled) wouldn't positively prove all four carbs are venting well. You would have to remove all bowls and feel/hear air with your hand enter the bowl chamber. After this, you would prove all four carbs are venting.
Obviously, your engine is acting as a vacuum. Literally sucking fuel from the carb(s), into the cylinder(s) and up through the top breather. I didn't think such amounts of fuel could enter though, as you describe. But vacuum is vacuum. You have excessive vacuum.
Only way you can have excessive vacuum is if the engines venting has been compromised. Only vent points besides the carb vents, are the breather, and a vent hole in the crankcase area. My '79 1000 has an open hole on the lower left side, behind the starter/stator area. Not sure where yours is located. The hole is generally large enough to put your finger in. I don't know how yours could become blocked if the bike just sat and no one worked on it. But it's possible. Locate it and check it. Maybe someone here with a similar model knows the hole I'm talking about if you have trouble.
All I know is, based on your exact description of the leaking, your venting is gone and the engine is acting as a vacuum.
Besides the above, what else could cause this? An exhaust valve(s) always closed or nearly closed? How could that happen if the bike ran fine, was turned off and then sat?
Obviously, your engine is acting as a vacuum. Literally sucking fuel from the carb(s), into the cylinder(s) and up through the top breather. I didn't think such amounts of fuel could enter though, as you describe. But vacuum is vacuum. You have excessive vacuum.
Only way you can have excessive vacuum is if the engines venting has been compromised. Only vent points besides the carb vents, are the breather, and a vent hole in the crankcase area. My '79 1000 has an open hole on the lower left side, behind the starter/stator area. Not sure where yours is located. The hole is generally large enough to put your finger in. I don't know how yours could become blocked if the bike just sat and no one worked on it. But it's possible. Locate it and check it. Maybe someone here with a similar model knows the hole I'm talking about if you have trouble.
All I know is, based on your exact description of the leaking, your venting is gone and the engine is acting as a vacuum.
Besides the above, what else could cause this? An exhaust valve(s) always closed or nearly closed? How could that happen if the bike ran fine, was turned off and then sat?
D
dietcokeking
Guest
Is there any chance that his fuel tank is not venting, causing pressure build-up to flood the carbs when the petcock opens upon starting the engine?
Naw. If the tank had poor or no venting, you would have poor or no fuel flow.dietcokeking said:
Very odd what's happening with this bike. After sitting for about 6 weeks or so I can see the float valves maybe varnishing up and not sealing or some common thing like that, but that kind of thing would cause fuel to rise inside the carb and then exit out the engine side and into the crank and also exit out the filter side and down into the airbox and out the airbox drain line.
For raw fuel to go up into the top of the engine and drain out the breather line is excessive vacuum. Like it's being pumped. I just can't see anything allowing this excessive vacuum except for no venting. And there aren't that many vents to check.
A
away_man
Guest
Many thanks to Keith; that is the type of info I've been looking for. The more I looked at this, I was leaning more towards a vacuum problem, rather than a carb problem (carb problem would have been better, in that it's expected, relatively easy to troubleshoot, and fairly easy to fix).
I'm definitely working on the bike starting first thing Monday morning, and your tips about engine venting give me some confidence that I'll actually have it running by Monday evening.
Regarding the vent hole, if anyone knows where it is on the 1100EZ, I'd be happy to find out. I just remembered, after Keith mentioned "no one worked on the bike"-- I did change the oil last fall, and it could have been before this issue started, probably around the same time.
Could I have screwed something up in a process as simple as an oil change to create this issue? I didn't do anything as blatantly obvious as forget to put a filter in or anything....
I'm definitely working on the bike starting first thing Monday morning, and your tips about engine venting give me some confidence that I'll actually have it running by Monday evening.
Regarding the vent hole, if anyone knows where it is on the 1100EZ, I'd be happy to find out. I just remembered, after Keith mentioned "no one worked on the bike"-- I did change the oil last fall, and it could have been before this issue started, probably around the same time.
Could I have screwed something up in a process as simple as an oil change to create this issue? I didn't do anything as blatantly obvious as forget to put a filter in or anything....
A
away_man
Guest
Lessons Learned...
Lessons Learned...
(First off, it's running! \\
/)
So, after checking to make sure the carb vents were open (before I replaced the bowls), I decided to change the oil. I pulled the drain plug on the oil pan, and....
THREE GALLONS (roughly) of gas (with some oil in it) came out of my engine. :shock: The tank was not on the bike at this time, and had not been for a couple of weeks. I'm not just guessing at the three gallon measure; I drained my oil collector into a 5-gallon container, and it was about 2/3 full.This would explain the unusual occurence of gas pumping out of the breather; the entire engine was so gas-logged that it had nowhere else to go.
I pulled the oil filter cover (more gas drained out), put a new filter in, put clean new oil in, got the carbs installed, and she's running like a top again (after I got the idle screw set where it's supposed to be).
I put it back on the sidestand until the weekend, when I'm going to give it another oil change, for two reasons. 1. Just to make sure there's no residual gas in this batch of oil, and 2. to make sure no new gas has leaked from the tank into this oil. I went for a spin around the block, but that's as far as she goes until I know I have gas-free oil in it.
I'm guessing (hoping, actually) that all that gas got in there in the first place becuase of the bad o-rings on the needle valve seats. Not sure how I managed to get *that much* gas into the engine, but I'm guessing it was something to due with the length of time I left it sitting on the sidestand, and maybe running the throttle improperly when I was trying to start it with a bad battery.
I'll have to keep an eye on my oil for a while and make sure I don't still have a petcock problem or some other undiscovered issue, but I have my fingers crossed that I'm all ready to go, just in time for warm weather.
Thanks much to all that helped me out on this one. =D> I'm hoping this is the last post I'll have to make on this thread.
-Aaron
P.S. (miscellaneous thoughts)
1. I could have saved myself a lot of headache (and looking silly) if I had changed my "oil" to begin with, but I was trying to get this gas problem resolved before I put good oil in, so I wouldn't waste oil. I'm sure there's a lesson about "penny wise and dollar foolish" or being a cheapskate in here somewhere...
2. For those who think I'm either crazy or deaf, the engine really did sound fine for the few seconds it was running with all that gas in there, every time I started it. I'm reasonably confident that it drowned quickly enough every time I started it that it didn't cause any serious damage from lack of lubrication.
3. You woulda thought it would have hydro-locked with all that gas in there....started right up every time when the battery was charged. Go figure...?
Thanks again to all.
Lessons Learned...
(First off, it's running! \\
/)So, after checking to make sure the carb vents were open (before I replaced the bowls), I decided to change the oil. I pulled the drain plug on the oil pan, and....
THREE GALLONS (roughly) of gas (with some oil in it) came out of my engine. :shock: The tank was not on the bike at this time, and had not been for a couple of weeks. I'm not just guessing at the three gallon measure; I drained my oil collector into a 5-gallon container, and it was about 2/3 full.This would explain the unusual occurence of gas pumping out of the breather; the entire engine was so gas-logged that it had nowhere else to go.
I pulled the oil filter cover (more gas drained out), put a new filter in, put clean new oil in, got the carbs installed, and she's running like a top again (after I got the idle screw set where it's supposed to be).
I put it back on the sidestand until the weekend, when I'm going to give it another oil change, for two reasons. 1. Just to make sure there's no residual gas in this batch of oil, and 2. to make sure no new gas has leaked from the tank into this oil. I went for a spin around the block, but that's as far as she goes until I know I have gas-free oil in it.
I'm guessing (hoping, actually) that all that gas got in there in the first place becuase of the bad o-rings on the needle valve seats. Not sure how I managed to get *that much* gas into the engine, but I'm guessing it was something to due with the length of time I left it sitting on the sidestand, and maybe running the throttle improperly when I was trying to start it with a bad battery.
I'll have to keep an eye on my oil for a while and make sure I don't still have a petcock problem or some other undiscovered issue, but I have my fingers crossed that I'm all ready to go, just in time for warm weather.
Thanks much to all that helped me out on this one. =D> I'm hoping this is the last post I'll have to make on this thread.
-Aaron
P.S. (miscellaneous thoughts)
1. I could have saved myself a lot of headache (and looking silly) if I had changed my "oil" to begin with, but I was trying to get this gas problem resolved before I put good oil in, so I wouldn't waste oil. I'm sure there's a lesson about "penny wise and dollar foolish" or being a cheapskate in here somewhere...
2. For those who think I'm either crazy or deaf, the engine really did sound fine for the few seconds it was running with all that gas in there, every time I started it. I'm reasonably confident that it drowned quickly enough every time I started it that it didn't cause any serious damage from lack of lubrication.
3. You woulda thought it would have hydro-locked with all that gas in there....started right up every time when the battery was charged. Go figure...?
Thanks again to all.
B
Billy Ricks
Guest
The o-rings on the float seats are one of the most often overlooked culprits with problems like this.
D
dietcokeking
Guest
I'm certain all that fuel entered the engine while you were storing the bike. Therefore, two things were occurring: 1. Fuel was seeping by the float needles; and 2. The petcock had been left on PRIME or the petcock is not working as designed.
The petcock should not flow fuel when the engine is stopped, except on PRIME. Of course, PRIME should only be used for the brief time necessary to manually fill the carb bowls with fuel, most often after carb service or if the bike had ran out of fuel. The bike should be stored with the petcock indicating ON (or RESERVE as the case may be).
You have to accept that our four float needles don't seal that well, or that reliably. However, unless things are really, really, really goofed up, float needles seeping at any expected rate aren't going to deposit gallons of raw fuel into the crankcase of a running engine (although that particular cylinder might be running rich).
An investment in a new petcock (or a cheaper rebuild kit) would eliminate this worry for you.
The petcock should not flow fuel when the engine is stopped, except on PRIME. Of course, PRIME should only be used for the brief time necessary to manually fill the carb bowls with fuel, most often after carb service or if the bike had ran out of fuel. The bike should be stored with the petcock indicating ON (or RESERVE as the case may be).
You have to accept that our four float needles don't seal that well, or that reliably. However, unless things are really, really, really goofed up, float needles seeping at any expected rate aren't going to deposit gallons of raw fuel into the crankcase of a running engine (although that particular cylinder might be running rich).
An investment in a new petcock (or a cheaper rebuild kit) would eliminate this worry for you.
If you didnt have a bad petcock, gas could not flow even if you removed the float needle valves and threw away the floats when the engine was not running. When the engine is running, fuel is drawn into the combustion chamber to be burned, not the crankcase. You probably do have faulty "O" ring seals on the fuel inlet valves, but it is for certain, the petock is BAD.
Earl
Earl
away_man said:
Hope you get the gas leak fixed.
Your latest findings make sense but with that much fuel in the motor, I don't see how gas was only noticable coming from the crankcase breather line. There should also have been fuel passing into the exhaust and dripping through the condensation holes at the bottom of the exhaust, and more would be backing out of the overflow tubes for the carbs. With the fuel ONLY leaking from the breather, it was quite a head scratcher.
Maybe you didn't notice fuel exiting at these other places but I have to believe it was after your latest description. That would have made it easier to figure out that your motor was simply filled to the maximum. Not a vacuum or venting problem, just simply too much fuel entered, due to a float valve(s) or bad petcock.
Any float valve problem I've ever seen showed fuel leaking out the carb and into the filter(s), besides into the engine.
Your latest findings make sense but with that much fuel in the motor, I don't see how gas was only noticable coming from the crankcase breather line. There should also have been fuel passing into the exhaust and dripping through the condensation holes at the bottom of the exhaust, and more would be backing out of the overflow tubes for the carbs. With the fuel ONLY leaking from the breather, it was quite a head scratcher.
Maybe you didn't notice fuel exiting at these other places but I have to believe it was after your latest description. That would have made it easier to figure out that your motor was simply filled to the maximum. Not a vacuum or venting problem, just simply too much fuel entered, due to a float valve(s) or bad petcock.
Any float valve problem I've ever seen showed fuel leaking out the carb and into the filter(s), besides into the engine.
Similar threads
