• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

Gas tank pin holes

  • Thread starter Thread starter Norseman
  • Start date Start date
N

Norseman

Guest
I stripped down my gas tank and used acetone to remove the Kreem sealer on the inside. The tank appeared to be in good shape, but to my dismay, two tiny pinholes on the bottom was revealed when I broke the Kreem seal (which was peeling in other areas).

My question is whether it's possible to solder these two pin holes, or do I need to get the POR-15 kit to seal the inside. If I can solder, does anyone have any instructions on how to effectively solder pin holes? I have the tank down to shiny metal on the outside.

I would appreciate any and all guidance, folks. Thanks.

Norseman
 
I've done a little research on this as I'm in the same predicament and the anwser is yes, you can do it but be careful as there is a possibility of the tank "flashing over" (exploding). I went with an epoxy (JB Weld) to fix my holes since my rust holes were a little more extensive and I wanted to go the cheap route for now.

You could also talk to a radiator shop or a welding shop and see if they could offer any insight/give you an estimate. Good luck and let us know how it works out.
 
A radiator shop can clean and seal the inside of any gas tank for about $50, or so, depending on where you are. I have had a number of tanks done that way, no worry about peeling or leaking, ever.
 
gsgeezer said:
A radiator shop can clean and seal the inside of any gas tank for about $50, or so, depending on where you are. I have had a number of tanks done that way, no worry about peeling or leaking, ever.
Click to expand...


I have also done this, and, for me, it is the only way to go.

You are obviously going to have to paint the tank again, so I would suggest stripping the tank before doing the inside.
 
If you are planning to do it yourself the MOST important thing is to be sure there is no residual fuel vaporizing in the tank. Since it sounds like you're going to have to do some additional prep work and repainting I would advocate submerging the entire tank in a large container full of water and Dawn dishwashing liquid, and let it soak for awhile while the petroleum is dissolved away...

Then you can be confident that soldering up the holes won't result in an "explosive" experience, but even so I'd use a small fan to continually blow fresh air into the tank while you work. You'll need more heat, but at least there won't be a build-up of explosive fumes. Obviously the tank will need to be "worked over" to remove any surface rust that might try to start between the repair and the re-coating/priming/painting.

Good luck with it!
 
Thanks to all of you for your suggestions and advice. The one thing I don't have to worry about is the paint - the tank is down to shiny metal.

I did not realize radiator shops will clean and seal gas tanks - that's great and I will go that route, thanks so much for that guidance. There are definitely no fumes left in the tank (two phosphoric baths, one acetone, then one final phosphoric, then thorough rinsing).

Norseman
 
You must log in or register to reply here.
Back
Top