• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

GS700 hard starts. sluggish 1/8 throttles

  • Thread starter Thread starter 5t341th
  • Start date Start date
5

5t341th

Guest
Hey guys. I am trying to figure out what is wrong with my bike as of now.
I have K&N pods and a supertrapp exhaust.
Things I've done:
strip and soak/clean the carbs
dynojet stage 3
new o-rings
"highest-idle" fuel mix screws method
I've also done the valves adjustment maybe 5 months ago. I am not sure if it was done right or not

What is troubling me is the difficult starts I have. It takes starting fluid to work. Without it, I would just drain the battery.

Also, I notice that while in gear and taking off, I would have a stumble at about 1/8 to 1/4 throttle. This is only in first gear. Once it passes, it rides fine (to me) in other gears

And if it matters, I have a broken stud in one of the exhaust ports so it does leak a bit out of the port. Would this add to my issue?

Any ideas on what I should do? I believe it is running lean? Is that correct?
 
Last edited:
The hard starts means your "choke" circuits are clogged. You are going to have to strip them down again.
The sluggish 1/8 throttle means your "fast idle" tuning was not done correctly.
It happens. I could not get the fast idle method to work on my bike so I wrote the procedure in my signature. Works for me.
 
Hard starts are also a classic symptom of mis-adjusted valves, especially the intakes.

Since you said you are not sure you did the adjustment correctly, I would do that while the carbs are soaking in "the dip" to clean the "choke" circuits.

.
 
Also double check you don't have a couple plugged pilot jets while you have the carbs apart again.
 
Hard starts also can be as a result of low voltage at the coils producing weak spark. On every one of the last 4 GSs I've owned the voltage at the coil, when the battery was fully charged at 12.5+ volts was 11.75volts or lower. One was at 10.8volts. The coil relay modification (see Cliff's site for the tutorial) is the solution.

Undoubtedly the carbs are still gummy and the valves may too be out of spec so I would recommend you check and redo each of these three things. Of late, I make these checks SOP on any new to me bike.

Good luck with it.
Spyug
 
well I am pretty sure it isnt the low voltage. I already did the coil relay mod. battery is new and i do get good voltage to the coils.

I will try checking out the valves first, then i will look into tearing into the carbs again.
thanks guys
 
i finally had time to perform some work. I readjusted the valves a bit since they were a bit tight. i pulled the plugs to check them out and they are all black! too rich right?
heres a picture. cylinder 1-4 left to right

and ray, i will contact you when i've run out of hope
 
Last edited:
looks like a lot of choke use.
the 2 center plugs are near acceptable but the outside plugs are fuel fouled.
another thing is once plugs are fuel fouled they will never recover 100%.
try a new set of plugs and see where your at once you have done what has been recommended in the other's post.

if the plugs are in order...maybe a coil/plug cap or ignitor problem.
1&4 looks bad in pic.
 
Last edited:
Things i've done yesterday.
replaced the spark plugs
adjusted the valves
reset the "air screws" back to 2.5 turns out

when i try to start it, it tries much better than before, but i do get backfire out of the exhaust. when it does start, adding throttle kills it. this tells me it is too lean?
 
oops looks like i connected the coils into the wrong cylinders.
fired it up and no problems. just need to test ride now
 
Anyone know if the bs32 air mix screws are interchangeable with the bs34? I asked z1 but they don't know and told me just to look at the pictures. I want to replace my mix screws because they are missing washers/oring anyway
 
Hello all again. I am back after all these years and my bike still has problems starting. Since last time, I've parked it for many years without use because of the issues and now I am back at it again.
Same mods as before but I've fixed the exhaust manifold leak and readjusted the valves again. I used new spark plugs and I have already done the coil relay mod.
I do have a question about how the coils should be connected to the plugs. Currently, left coil is plugged into #1 and #3 and the right coil is on #2 and #4. Is this right?
If and when the bike starts, it's usually after many many many minutes of cranking and setting full choke. The bike idles poorly and backfires out of the exhaust and sometimes pods. What could be causing my issues? With the pods installed, the bike does seem to try to start better. The pods are old and tired, so could that be a problem?
So to clarify, I have
-super trapp exhaust
-k&n pods
-dynojet stage 3 with 134 mains
-coil relay mod
-new battery
-idle mix screws set at 3 turns out
-freshly adjusted valves
-new oil
-new plugs
-new o-rings and intake boot rings from the last time around

PS. where can I get new idle mix screws with spring, orings?
 
Last edited:
5t341th said:
Hello all again. I am back after all these years and my bike still has problems starting. Since last time, I've parked it for many years without use because of the issues and now I am back at it again.
Same mods as before but I've fixed the exhaust manifold leak and readjusted the valves again. I used new spark plugs and I have already done the coil relay mod.
I do have a question about how the coils should be connected to the plugs. Currently, left coil is plugged into #1 and #3 and the right coil is on #2 and #4. Is this right?
If and when the bike starts, it's usually after many many many minutes of cranking and setting full choke. The bike idles poorly and backfires out of the exhaust and sometimes pods. What could be causing my issues? With the pods installed, the bike does seem to try to start better. The pods are old and tired, so could that be a problem?
So to clarify, I have
-super trapp exhaust
-k&n pods
-dynojet stage 3 with 134 mains
-coil relay mod
-new battery
-idle mix screws set at 3 turns out
-freshly adjusted valves
-new oil
-new plugs
-new o-rings and intake boot rings from the last time around

PS. where can I get new idle mix screws with spring, orings?
Click to expand...

No, left coil should be connected to 1 and 4, with right coil on 2 and 3. The plug caps on leads for 2 and 3 are longer than the caps on leads for 1 and 4.
 
When was the last time you cleaned the carburetors per Nessism's guide and adjusted the valves (you say you did them again but when)? What are your readings for each cylinder both in clearance and current shim size?

What's the current jet sizes if you are using the pods? Is there a reason you can't go back to the stock air box?
 
Both the wires on my coils have a long and short wire. I will try putting them on 1,4 and 2,3.
I adjusted my valves yesterday to the specs. 0.07 is what I set themy to. I do not have shims, only tappets. I took apart the carbs and gave them a once over, but I didn't dip them again like before. My bike is a 85 gs700e
 
You must log in or register to reply here.
Back
Top