• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

Help removing rear axel!

  • Thread starter Thread starter mortation
  • Start date Start date
M

mortation

Guest
The rear caliper mount that goes around the rear axel and the spacer on the outer side of it are FROZEN to the axel. I have been spraying it with Free all and PB blaster and pushing pulling hitting and I still cant get it to break free. Anyone have any suggestions???
 
Have you got the axle out from the rear wheel?

Best bet would be to either let it have a long soak in parafin, old oil or deisel to allow lubrication to get in.

If not put some heat from a paint stripper, hair dryer or if you have one a torch (hopefully the right word this time) as aluminium and steel will expand and contract at different rates.

Worse case is getting somebody with a hydralic press push the bolt out from the space and rear brake bracket.

suzuki mad.
 
Last edited:
It may also be the bearing support in the hub that is sticking to the axle. Put the nut back on backwards and give it a good hard whack.
 
Billy Ricks said:
It may also be the bearing support in the hub that is sticking to the axle. Put the nut back on backwards and give it a good hard whack.
Click to expand...

Na. It slides freely back and forth a little bit except where the spacer and bracket prevent it from sliding any more in either dirrection. Those things are definately the culprit. I am running to the HW store and grabbing a cheap ass little torch.
 
Hair dryer heat!

Hair dryer heat!

mortation said:
Think a hair dryer will produce enough heat?
Click to expand...


Have you tried one? Didn't have any sort of flamed heat in the garage so used a hair dryer to warm up the rotor/crankshaft to get at a starter clutch. I was supprised after 5 minutes just how hot the rotor had got!

Suzuki mad.
 
Suzuki mad said:
If not put some heat from a paint stripper, hair dryer or if you have one a torch (hopefully the right word this time) as aluminium and steel will expand and contract at different rates.
Click to expand...
Very good, there, SM. \\:D/ Unless your "flashlight" is really bright, :shock: it won't be hot enough to use as a torch. 8-[


Mortation,
My only suggestion would be to make sure that you have released ALL the bolts that clamp the axle into place. Evidently this is on your 850? That means it is a shaftie, and I can just go out to the garage and sneak a peek. There is a bolt at the end of the right side of the swingarm that locks the axle into place. Have you loosened that?


.
 
Mr. mortation,

There is a little circular ring on the right swing arm and a corresponding one on the right side of the frame. After you've loosened/removed your shocks (you at least have to disconnect one end of your shocks), lift the wheel and stick a phillips head screw driver through both of these circles to hold the wheel up. When I removed my wheel, I had to then use a lift (a hydraulic jack) to lift the wheel/tire slightly to take the pressure off the axle so that it would slide out. If you don't have a jack you may have to get creative with wood blocks and some kind of fulcrum. I still had to take a hammer and a piece of wood (like a small length of broom handle) to gently "persuade" the axle to come out. Make sure the wheel is straight and not binding the axle making it hard to slide out.

Have you taken out the bolt that holds the rear brake line? The spacers and rear caliper assembly won't come out until the axle is out of the way. Forgive me if I state the obvious.

Thank you for your indulgence,

BassCliff
 
Last edited:
Seems like you could take a socket extender and hammer away on the end of the axle without damaging the threads or the axle. Probably some rusted crud building up a little ridge on the axle.
 
You must log in or register to reply here.
Back
Top