• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

Horn Trouble

chuckycheese

chuckycheese

Forum Sage
Past Site Supporter
Charter Member
OK, all you experts, here's the problem!!
I bought a new horn for my bike and it sounds great while the bike is idleing in the driveway, but......on the road, it sounds weak and unsteady. I don't think the vibration is causing a problem and the wiring seems to be fine but the best tone I ever get is when it's standing still. I can even rev it up and it still works great. I feel sure the problem is simple but I don't know what it might be. I will appreciate your thougts!! :oops:
 
Sounds like you may have the horn mounted very close to the frame, and at speed it is flexing back just enough to contact the frame where its necessary vibration is being damped.

If this applies, the cure is simple: try changing the position, or put a spacer behind, to give it a bit more clearance.

If not, wait a bit. I'm sure more suggestions will follow... :)
 
You may also want to clean out the contact on the horn switch
 
Thanks

Thanks

Well, thanks, so far. It's not touching the frame and....remember, it works great when the bike is sitting in one spot; even going through considerable vibration when revving up so....I'm stumped. I think it's got to be some kind of electrical problem but it must be more complicated than grounding. :lol:
 
It appears your only other option is wiring.

Back to the flex idea

You have two very thin wires running to the horn, one live and one ground. One is live as long as the ignition is ON, and the ground goes to your horn switch.

Check the terminals, but also check the wires themselves...they are very small and subject to breaking internally. You may find the strands inside one or both have mostly broken, and now make intermittent contact as the wire flexes in the wind.

This would usually happen at or near the terminals, so replacing or refastening the terminals may be what's necessary.

Even if a few strands have broken, this could apply, as there isn't much there to begin with, so the few remaining bits may not be able to carry the current needed to blow the horn.

Splicing the wires all the way back requires opening up the harness, and that is time-consuming as the splice inside the harness is back about ten inches. (The splice is to the orange/white wires that power the signal lights.) If you make an external splice, do it close to the harness and tape the new one(s) to it for an inch or so.

Having had the experience, I would leave opening the switch as a last resort, because there are tiny parts inside it that just love to jump out and disappear.

If you do it, it's probably best to have a large clear plastic bag around it and work inside the bag while looking through it.
 
I believe Roy is on the right track about the thin wires. I had the same problem. Bought a new horn, and still had the same problem. I took the easy way out. There was enough current to operate a relay, which was wired directly to the battery terminals. Now my horn works perfectly.

Erik
 
You must log in or register to reply here.
Back
Top